Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: 1941 NEW YORKER


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
RE: 1941 NEW YORKER
Permalink  
 


sasquatch wrote:

Just bein nosey checking out the background in the pics of your'e shop, wondering,, is that a Logan or Rockwell metal lathe, and i noticed you also have a mill/drill there also. Lol

Shop stuff always attracts interest!!


Its a West Bend 9" lathe.

The mill was busy bee and has been sold. There is now a nice Bridgeport in one corner of the garage.



__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

fatstax wrote:

when i was planning my rat truck frame, i considered using eighth wall tubing but instead i used three sixteen wall, i was concerned my truck wouldnt be heavy enough and might be wonky to drive.  have you thought of this?  you appear to be using eighth wall.  you rod might be pretty light but it looks like it will be like a sports car with higher tech suspension than my build so there may be no need to add weight.


 Hey stax.

My car will have no lightness problems. The New Yorker has a 128" wheel base, its huge. It should be 4000 lbs by the time I'm done.

BTW, wonky to drive = my ultimate goal.

I'm hoping for 600 FT/LBS and 500 HP.



__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

I started on the rear lower control arms.

The cast aluminum would have been OK except they had no set up for coil overs.

I started with some sched 80 s/s pipe for the pivot tubes. The bushings are aftermarket Delrin.

I had to weld in some 14 ga s/s sleeves to get them sized just right.

 

IMG_1241 (Medium).jpg

 

IMG_1244 (Medium).jpg

 

IMG_1246 (Medium).jpg

 

I had a couple of pieces of 1-1/2" round 1/8 wall tube bent to shape. I made a jig using the stock control arm to get things dead on.

IMG_1249 (Medium).jpg

 

IMG_1251 (Medium).jpg

 

IMG_1252 (Medium).jpg

 

IMG_1254 (Medium).jpg

 

IMG_1256 (Medium).jpg

 

IMG_1261 (Medium).jpg

 



-- Edited by 123pugsy on Friday 14th of September 2012 05:30:14 PM

Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

I added two cross braces to really stiffen things up.

 

IMG_1287 (Medium).jpg

 

IMG_1296 (Medium).jpg

 

IMG_1300 (Medium).jpg

 

IMG_1302 (Medium).jpg

 

IMG_1304 (Medium).jpg

 

IMG_1305 (Medium).jpg

 

IMG_1306 (Medium).jpg

 

IMG_1312 (Medium).jpg

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Had to get coilover mounts and sway bar link hook up points done next.

 

IMG_1315 (Medium).jpg

 

IMG_1319 (Medium).jpg

 

 

IMG_1320 (Medium).jpg

 

 

IMG_1321 (Medium).jpg

 

 

IMG_1323 (Medium).jpg

 

 

IMG_1325 (Medium).jpg

 

 

IMG_1385 (Medium).jpg



Attachments
__________________
PUGSY


ONTARIO

Status: Online
Posts: 1476
Date:
Permalink  
 

Danm, cna't type rihgt, I'm slobbreing all ovre the kyeboard.

__________________


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Iwannagofast wrote:

Danm, cna't type rihgt, I'm slobbreing all ovre the kyeboard.


 LOL ......!!!!!

Thanks.



__________________
PUGSY


NORTH BAY, ONT

Status: Offline
Posts: 3717
Date:
Permalink  
 

Beautiful workmanship,, and excellent photos!!

P.S. Your'e metal lathe MUST be a "South Bend" not a "West Bend" Lol

(They made coffee pots.)

__________________


NIAGARA FALLS, ONT

Status: Offline
Posts: 545
Date:
Permalink  
 

Dang Pugsy, you don't mess around!! Words simply can't describe how great your chassis is coming out.   



__________________

Nick M.

A journey in design and fabrication begins with a vision, a single pen stroke ... and in some cases the blow of a hammer.



MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Thanks Guys.

BTW, my milling machine is actually a Cuisinart, but I said Bridgeport to try to keep it sounding cool.

__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

The next order of business was the front kick ups.

 

IMG_1548 (Medium).jpg   

 

IMG_1557 (Medium).jpg

 

IMG_1564 (Medium).jpg

 

 

IMG_1565 (Medium).jpg

 

 

IMG_1566 (Medium).jpg

 

 

IMG_1568 (Medium).jpg

 

IMG_1569 (Medium).jpg

 

 

IMG_1570 (Medium).jpg

 

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

More of the same....

 

IMG_1573 (Medium).jpg

 

 

IMG_1575 (Medium).jpg

 

 

IMG_1576 (Medium).jpg

 

 

IMG_1578 (Medium).jpg

 

 

IMG_1579 (Medium).jpg

 

 

IMG_1583 (Medium).jpg

 

 

IMG_1584 (Medium).jpg

 

 

IMG_1587 (Medium).jpg

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Crossmember was next....

 

 

IMG_1538 (Medium).jpg

 

IMG_1541 (Medium).jpg

 

IMG_1542 (Medium).jpg

 

IMG_1544 (Medium).jpg

 

IMG_1549 (Medium).jpg

 

IMG_1552 (Medium).jpg

 

IMG_1612 (Medium).jpg

 



 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

More crossmember......

 

IMG_1621 (Medium).jpg

 

 

IMG_1605 (Medium).jpg

 

 

 

 

IMG_1623 (Medium).jpg

 

 

IMG_1625 (Medium).jpg

 

 

IMG_1626 (Medium).jpg

 

 

IMG_1630 (Medium).jpg

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Crossmember continued...

 

 

IMG_1987 (Medium).jpg

 

 

IMG_1989 (Medium).jpg

 

 

IMG_1992 (Medium).jpg

 

 

IMG_1993 (Medium).jpg

 

 

IMG_1995 (Medium).jpg

 

 

IMG_1996 (Medium).jpg

 

 

IMG_1998 (Medium).jpg

 

 

 

IMG_1999 (Medium).jpg

 

 

 



Attachments
__________________
PUGSY


LINDSAY, ONT

Status: Offline
Posts: 633
Date:
Permalink  
 

Now that my friends is a beautiful thing!!

__________________

Adam - '65 Ford F-250 Custom

LOSERS CAR CLUB

 



MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Thanks Adam.

The next order of business was to make the upper control arms.

First thing was to get a computer program for checking the front end geometry.

ANALYZER.jpg

 

ANALYZER ROLL.jpg

Found these screw in ball joint sleeves at Horton's. I couldn't weld the steel to my stainless arms, so I got some more sched 80to wrap them in.

Bored them out and chamfered.

IMG_1225 (Medium).jpg

Sqeezed them into place....

IMG_1226 (Medium).jpg

 

 

IMG_1229 (Medium).jpg

Welded them up with s/s rod.

IMG_1418 (Medium).jpg

 

A couple of pieces of s/s pipe for the pivot sleeves and made up a jig. I had some 1" diameter, 1/8 wall tube bent up for these.

IMG_1769 (Medium).jpg

 

The sleeves warped like crazy from the welding. I joined two files together to hog out as much of the warped material as possible.

IMG_1801 (Medium).jpg

 

IMG_1806 (Medium).jpg

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Lower control arm ball joint sleeves. I'm using stock Cobra press in ball joints.

 

 

IMG_1417 (Medium).jpg

 

This pic shows the nice fit after pressing in a ball joint and taking it out.

 

IMG_1425 (Medium).jpg

 

 

 

IMG_1423 (Medium).jpg

 

 

 

 

 

 

Here's something funny. I started my lower arms and thought I had really nailed a great design.

Of coarse if the car only went straight they'd be wonderful.

 

 

IMG_1648 (Medium).jpg

 

 

 

IMG_1665 (Medium).jpg

 

 

 

IMG_1666 (Medium).jpg

 

 

 

IMG_1774 (Medium).jpg

 

How's that for clearance?

 

IMG_1781 (Medium).jpg

 

 

 

IMG_1784 (Medium).jpg

 

 

 

 



-- Edited by 123pugsy on Sunday 14th of October 2012 07:26:23 AM

Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Upper control arms welded and polished after hand reaming for hours to true up the sleeves for the bushings.  I gave up trying to get them all the same. I now have a log of all the different sized bushings in case they need replaced.

 

IMG_1791 (Medium).jpg

 

 

 

IMG_1793 (Medium).jpg

 

 

 

IMG_1974 (Medium).jpg

 

 

 

IMG_1977 (Medium).jpg

 

The upper arm mount plates are 1/2'' s/s with slots to adjust caster. Camber is adjusted by adding equal amount of shims behind the plate front and rear.

 

IMG_1972 (Medium).jpg

 

 

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Coilover mounts.

 

IMG_2081 (Medium).jpg

 

 

 

IMG_2082 (Medium).jpg

 

 

 

 

IMG_2102 (Medium).jpg

 

 

 

IMG_2105 (Medium).jpg

 

 

 

IMG_2108 (Medium).jpg

 

 

 

IMG_2112 (Medium).jpg

 

 

 

IMG_2114 (Medium).jpg

 

 

 

IMG_2116 (Medium).jpg

 

 

 

IMG_2115 (Medium).jpg

 

 

 

IMG_2117 (Medium).jpg

 

 

 

 

 

 



Attachments
__________________
PUGSY


FINCH, ONT

Status: Offline
Posts: 1261
Date:
Permalink  
 

nothing to say but damn thats turning into one killer frame.Almost a shame to put a car on top of it.

__________________

 ///// Join THE LOSERS c.c. of Ontario Ask me how/////

LOSERS CAR CLUB



BRAMPTON, ONT

Status: Offline
Posts: 274
Date:
Permalink  
 

You have me drooling with all your beautiful fab work.

__________________


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Of coarse matching motor mounts were in order...........

 

 

IMG_2244 (Medium).jpg

 

 

 

IMG_2250 (Medium).jpg

 

 

 

IMG_2339 (Medium).jpg

 

 

 

IMG_2340 (Medium).jpg

 

 

 

 

 

 

 

 

Of coarse by this time in, I was due for another screw up.  I needed three U joints to get the steering shaft around the mounts so it was time for some new ones.

 

 

 

 

 

 

IMG_3629 (Medium).jpg

 

 

 

IMG_3645 (Medium).jpg

 

 

 

IMG_3648 (Medium).jpg

 

 

 

IMG_3655 (Medium).jpg

 

 

 

IMG_3656 (Medium).jpg

 

 

 

IMG_3908 (Medium).jpg

 

 

 

 

 

 

 



-- Edited by 123pugsy on Sunday 14th of October 2012 05:27:44 PM

Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Transmission crossmember.............

 

 

IMG_2295 (Medium).jpg

 

 

 

IMG_2297 (Medium).jpg

 

 

 

IMG_2300 (Medium).jpg

 

 

 

IMG_2319 (Medium).jpg

 

 

 

IMG_2330 (Medium).jpg

 

 

 

IMG_2333 (Medium).jpg

 

Gotta love stainless. It warps like crazy. If you scroll back 2 pics you'll see how warped the crossmember is. Clamped and heated and squeezed with the clamps until it straightened out.

 

IMG_2348 (Medium).jpg

 

 

 

IMG_2349 (Medium).jpg

 

 

Mount bracket for the....................

 

IMG_2352 (Medium).jpg

 

 

 

 

Gearvendors overdrive behind the 4L80E overdrive tranny. 

This allows me to weld the crossmember in as I can drop the tranny by first removing the Gearvendors unit.

 

 

IMG_2354 (Medium).jpg

 

 

 



-- Edited by 123pugsy on Sunday 14th of October 2012 05:40:26 PM

Attachments
__________________
PUGSY


NORTH BAY, ONT

Status: Offline
Posts: 3717
Date:
Permalink  
 

Agreed, can't say much more than damned nice work!!

__________________


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

 

Thanks Guys.

 

Drilled holes for the upper arm plates and inserted anti crush sleeves into the tube.

 

 

IMG_2135 (Medium).jpg

 

I got the idea for these adjusting washers from my IRS upper control arm bolts. The bolt has a built in washer on an eccentric. I didn't want to weld to a bolt and weaken it so I figured just a washer would do. I cut the haeds off some allan bolts and tacked them in so the alignment guy can tweak on them a little by little and move the upper arm forward or back.

 

IMG_2136 (Medium).jpg

 

 

 

IMG_2139 (Medium).jpg

 

 

 

IMG_2142 (Medium).jpg

 

 

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

ROLLING (but not complete) CHASSIS....................

 

 

IMG_2146 (Medium).jpg

 

 

 

IMG_2148 (Medium).jpg

 

 

 

IMG_2149 (Medium).jpg

 

 

 

IMG_2150 (Medium).jpg

 

 

 

IMG_2153 (Medium).jpg

 

 

 

IMG_2154 (Medium).jpg

 

 

 

IMG_2160 (Medium).jpg

 

 

 

IMG_2161 (Medium).jpg

 

 

 

IMG_2164 (Medium).jpg

 

 

 

IMG_2166 (Medium).jpg

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

More of the same..........

 

IMG_2167 (Medium).jpg

 

 

 

IMG_2171 (Medium).jpg

 

 

 

IMG_2173 (Medium).jpg

 

 

 

IMG_2174 (Medium).jpg

 

 

 

IMG_2175 (Medium).jpg

 

 

 

IMG_2181 (Medium).jpg

 

 

 

 

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Front body mounts...........

 

 

IMG_3109 (Medium).jpg

 

 

IMG_3110 (Medium).jpg

 

 

IMG_3115 (Medium).jpg

 

 

IMG_3130 (Medium).jpg

 

 

IMG_3137 (Medium).jpg

 

 

IMG_3159 (Medium).jpg

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Radiator.............

 

Made some aluminum ears for two pieces of 1/4'' side plates that will get welded to the sides of the rad to spread the load of the mounting. Don't want to be far from home when the side of the rad splits from the piece I welded on.

 

IMG_3241 (Medium).jpg

 

 

 

IMG_3246 (Medium).jpg

 

 

 

IMG_3247 (Medium).jpg

 

 

 

IMG_3251 (Medium).jpg

 

 

 

IMG_3260 (Medium).jpg

 

 

 

IMG_3269 (Medium).jpg

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

 

Back to the body.

Next order of business was to stiffen up the engine compartment opening.

Started with some brake formed angles. A bit of stretching and shrinking and the parts were ready to weld.

The last pic shows how I'd like to finish the rim off.

 

IMG_4157 (Medium).jpg

 

 

IMG_4165 (Medium).jpg

 

 

IMG_4168 (Medium).jpg

 

 

IMG_4174 (Medium).jpg

 

 

img_4181.JPG

 

 

IMG_4186 (Medium).jpg

 

 

IMG_4186A (Medium).JPG

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

I made up a jig to tack in the headlight plates and to try to get everything straight and true this time.

 

IMG_4186B(Medium).JPG

 

 

IMG_4238 (Medium).jpg

 

 

IMG_4241 (Medium).jpg

 

 

IMG_4241A (Medium).JPG

 

 

IMG_4257 (Medium).jpg

 

 

IMG_4260 (Medium).jpg

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

 

Got the headlight plates welded and one side cleaned up yesterday.

I  installed one headlight to see how she'd look......

 

IMG_4306 (Medium).jpg

 

 

 

IMG_4309 (Medium).jpg

 

 

 

IMG_4314a (Medium).jpg

 

 

 

IMG_4322 (Medium).jpg

 

 

 



Attachments
__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

 

I liked what I saw so much that I went ahead and cut the second hole out.

(I also need the hole to help planish the weld.)

 

 

 

IMG_4324 (Medium).jpg

 

 

 

IMG_4325 (Medium).jpg

 

 

 

IMG_4326 (Medium).jpg

 

 

That's got the project thread right up to date up until about an hour and a half ago.

 

Thanks for gawkin at me build,

 

 

 

 

 



Attachments
__________________
PUGSY


NORTH BAY, ONT

Status: Offline
Posts: 3717
Date:
Permalink  
 

Beautiful piece of workmanship!!!

Thanks for posting all the great pics of this build, interesting and enjoyable !

__________________


BRAMPTON, ONT

Status: Offline
Posts: 274
Date:
Permalink  
 

I love how you fab everything yourself. Everything looks amazing!

__________________


ONTARIO

Status: Offline
Posts: 4606
Date:
Permalink  
 

You never did mention what engine you were running ! Please, please, please don't tell me it's Chev or Ford powered?? All that work, this car must be Chrysler powered !! It would make it faster too !

 

Edit; Never mind ! I read an earlier post you made and noticed you were using a 4l80E. I'm crushed !! LOL

I really wanted to see something like a 6.1 Hemi in it The price of stainless will go through the roof because you've used it all in that frame. I keep away from stainless because that's one material I hate working with. Will interesting to see how it handles the stresses of the frame. Nice work !!



-- Edited by hemi43 on Tuesday 27th of November 2012 10:00:00 AM

__________________


BRANTFORD, ONT

Status: Offline
Posts: 2269
Date:
Permalink  
 

AMAZING ! ABSOFORKINGLUTLY AMAZING!



-- Edited by Grumpsbodyworks on Tuesday 27th of November 2012 10:20:15 AM

__________________

"If you don't pass on the knowledge you have to others, it Dies with you"



MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Thanks Guys.

Its a labour of love. I love to get away from the wife and keep tapping away in the garage.

I'll never make a living at it. I'm still trying to get my head around this shaping business 4 years later.

__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Sorry,

Engine will be a 496 stroker. Sequential fuel injection using an LSx ECM. I got an Edelbrock Pro Flo XT for the top and aluminum GM Performance (read Edelbrock) oval port heads. Will be a mild cam and stock convertor. Looking for a boat load of torque. Horsepower doesn't matter. That's a word that's not in my vocabulary. confuse

I was gonna go with a 6.1 Hemi but I'm a loyal Chevy guy. It hurt enough draggin a Chrysler home and shoving it in the garage. no

So, its pretty good that I've got the Big Three covered on this build. I've also got some Harley Davidson parts going into the build to make sure its really well rounded and I have the best of all the players.



__________________
PUGSY


NIAGARA FALLS, ONT

Status: Offline
Posts: 545
Date:
Permalink  
 

Wow Pugsy!

With those headlights mounted the shape of the front clip looks very sexy! Can't wait to see it back on the car.  Now get back in the shop to get some more work done ... to keep the photos coming.  smilesmilesmile



__________________

Nick M.

A journey in design and fabrication begins with a vision, a single pen stroke ... and in some cases the blow of a hammer.



ONTARIO

Status: Offline
Posts: 4606
Date:
Permalink  
 

123pugsy wrote:

I was gonna go with a 6.1 Hemi but I'm a loyal Chevy guy. It hurt enough draggin a Chrysler home and shoving it in the garage. no

____________________________________________________________________________________________________________________________

Well we can't all be perfect !! LOL  I guess that's the difference between Chevy and Mopar guys. I'm a loyal Mopar guy, and would have a difficult time putting a Chev in my shop.

 



__________________


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

I'm glad I went with the Chrysler though even if I'm a Chevy fan.

There sure aren't many out there so no one's gonna have the same car. With the custom snout, it'll be a one of a kind so that's even better.

__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

Grumpsbodyworks wrote:

AMAZING ! ABSOFORKINGLUTLY AMAZING!



-- Edited by Grumpsbodyworks on Tuesday 27th of November 2012 10:20:15 AM


 Thanks Grumpy.



__________________
PUGSY


MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

invision wrote:

Wow Pugsy!

With those headlights mounted the shape of the front clip looks very sexy! Can't wait to see it back on the car.  Now get back in the shop to get some more work done ... to keep the photos coming.  smilesmilesmile


 Thanks Nick.

Its nice to see a change in the project.

Now I just got to go use the hole I made for the headlight pot to start planishing again. I got about a million hours of metal finishing to do now....no



__________________
PUGSY


CLINTON, ONT

Status: Offline
Posts: 3909
Date:
Permalink  
 

123pugsy wrote:
Grumpsbodyworks wrote:

AMAZING ! ABSOFORKINGLUTLY AMAZING!

------------------------------------------------------------------

 

x2    You should really get a job doing this   winkwink

 



__________________

 

 



MARKHAM, ONT

Status: Offline
Posts: 1373
Date:
Permalink  
 

427CARL wrote:
123pugsy wrote:
Grumpsbodyworks wrote:

AMAZING ! ABSOFORKINGLUTLY AMAZING!

------------------------------------------------------------------

 

x2    You should really get a job doing this   winkwink

 


Thanks Carl.

I'd like to build rods for a living but I got to eat and send a couple of kids thru school.



__________________
PUGSY


BRANTFORD, ONT

Status: Offline
Posts: 2269
Date:
Permalink  
 

Pugsy,

Your right.....I have people tell me all the time to build full time..........but........ People dont want to pay $65-70 p/h

There are only so many whales that can afford too....and I haven't found one yet!

So....like you I build for myself and a select few friends.

You have amazing skills and I wont miss your class next year......gotta love stainless tig work.....amazing absofreeknlutly amazing.

Builders like you make me strive to build better !

__________________

"If you don't pass on the knowledge you have to others, it Dies with you"



WALKERTON, ONT

Status: Offline
Posts: 865
Date:
Permalink  
 

WOW -- I really don't know what else to say. Thanks for sharing. Really gotta love this site!

__________________


TORONTO, ONTARIO

Status: Offline
Posts: 264
Date:
Permalink  
 

 

now thats a beautiful looking front end if ive ever seen one

 
 I can offically say Ive been taught by one of the greats


__________________

Smoke tires, not drugs..

«First  <  1 2 3 47  >  Last»  | Page of 7  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard