Members Login
Username 
 
Password 
    Remember Me  
Forum Rules (Click Here) -> Ontario Rodders -> General Car Talk -> Driveshaft Cutting GTA
Post Info TOPIC: Driveshaft Cutting GTA
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Driveshaft Cutting GTA
Permalink  
 

Anyone know a place in the GTA to get a driveshaft cut?

 

Thanks.



__________________
PUGSY
poncho62


ADMINISTRATOR

Status: Offline
Posts: 3829
Date:
Permalink  
 

Here is one in Whitby..... drivelinewhitby.com

I would go to a local transmission shop and ask, they should know someone

__________________
wuga


PRINCE EDWARD COUNTY, ONT

Status: Offline
Posts: 1282
Date:
Permalink  
 

I had one done at Drive Line Whitby. He was amazing.

Warren

__________________
You can only make it better
Model A Guy


STROUD, ONT

Status: Offline
Posts: 447
Date:
Permalink  
 

Dynamic Shaft    589 Middlefield Scarborough 416-321-1075

Always satified with their work, but not necessarily cheap.



__________________

Don't Ask Me I'm As Dumb As a Shoelace!
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

Thanks Guys.

I will check Dynamic first. They are 5 minutes away. I went there about 15 years ago and they weren't cutting them then. They sent me to Driveline on Midwest Rd, but they closed up.

__________________
PUGSY
77


BARRIE, ONTARIO

Status: Offline
Posts: 1397
Date:
Permalink  
 

is astro joint still in business

__________________

I,m as cool as Milner , but axeually a bit more like Beckwith
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

77 wrote:

is astro joint still in business

 

Tried googlin.........Chevy Astro and doobies show up.



__________________
PUGSY
shag766


FOXBORO, ONT

Status: Offline
Posts: 2237
Date:
Permalink  
 

123pugsy wrote:
77 wrote:

is astro joint still in business

 

Tried googlin.........Chevy Astro and doobies show up.

 that's where i would go after the cutting has been done, lol



__________________
if your not the lead dog-the view is all the same
shag766


FOXBORO, ONT

Status: Offline
Posts: 2237
Date:
Permalink  
 

wuga wrote:

I had one done at Drive Line Whitby. He was amazing.

Warren

 i have had a couple of them done there over time, they did a good job.



__________________
if your not the lead dog-the view is all the same
Sniper


WATFORD, ONT

Status: Offline
Posts: 480
Date:
Permalink  
 

Check with the heavy truck guys, Freightliner, Mack, Peterbuilt etc. they would know who, and where to go.

__________________
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

Thanks.

Someone gave me these guys. 165 bucks. I made sure not to tell them 69 El Camino.

It would probably be $400.00 if I did that.

http://patsdriveline.com/locations/



__________________
PUGSY
shag766


FOXBORO, ONT

Status: Offline
Posts: 2237
Date:
Permalink  
 

Sniper wrote:

Check with the heavy truck guys, Freightliner, Mack, Peterbuilt etc. they would know who, and where to go.

 there are a couple of places around dixie rd north of the 401 that do mostly truck shafts. be easier for him to run to whitby from the markham area i would guess.



__________________
if your not the lead dog-the view is all the same
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

shag766 wrote:
Sniper wrote:

Check with the heavy truck guys, Freightliner, Mack, Peterbuilt etc. they would know who, and where to go.

 there are a couple of places around dixie rd north of the 401 that do mostly truck shafts. be easier for him to run to whitby from the markham area i would guess.

Thanks.

Actually, our driver goes to the area every week.

Engine and tranny are going in tonight and I will measure it up and send it tomorrow.

Only one problem. If you're supposed to measure when it's on the ground and you can't fit underneath, WT??

Or is there a method where I should deduct X/X"  to allow for the hanging suspension?



__________________
PUGSY
Lightspeed Mike


BELLEVILLE, ONT

Status: Offline
Posts: 959
Date:
Permalink  
 

123pugsy wrote:
shag766 wrote:
Sniper wrote:

Check with the heavy truck guys, Freightliner, Mack, Peterbuilt etc. they would know who, and where to go.

 there are a couple of places around dixie rd north of the 401 that do mostly truck shafts. be easier for him to run to whitby from the markham area i would guess.

Thanks.

Actually, our driver goes to the area every week.

Engine and tranny are going in tonight and I will measure it up and send it tomorrow.

Only one problem. If you're supposed to measure when it's on the ground and you can't fit underneath, WT??

Or is there a method where I should deduct X/X"  to allow for the hanging suspension?

 Just jack up the rear suspension when you have it in the air. Then measure.



__________________

Custom CNC plasma cutting. PM me for your custom parts.

www.lightspeedmetaldesign.com
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

Lightspeed Mike wrote:
123pugsy wrote:
shag766 wrote:
Sniper wrote:

Check with the heavy truck guys, Freightliner, Mack, Peterbuilt etc. they would know who, and where to go.

 there are a couple of places around dixie rd north of the 401 that do mostly truck shafts. be easier for him to run to whitby from the markham area i would guess.

Thanks.

Actually, our driver goes to the area every week.

Engine and tranny are going in tonight and I will measure it up and send it tomorrow.

Only one problem. If you're supposed to measure when it's on the ground and you can't fit underneath, WT??

Or is there a method where I should deduct X/X"  to allow for the hanging suspension?

 Just jack up the rear suspension when you have it in the air. Then measure.

 D'OH! Of course. I can use the tranny jack. Car is on the hoist.



__________________
PUGSY
123pugsy


MARKHAM, ONT

Status: Offline
Posts: 1344
Date:
Permalink  
 

Pat's did what appears to be a good job of it. Haven't installed it yet.

__________________
PUGSY
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Forum Rules (Click Here) -> Ontario Rodders -> General Car Talk -> Driveshaft Cutting GTA


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard