Tech

Cuddles · Cuddles

Good morning: I should have the floor panels in shortly but wonder where to get the carpeting normally installed in cars? It is very low profile and has a nice trim to it. I'd like to custom fit it if I can find where to get it and how to trim it? Any advice would be appreciated. Thanks to all.

Torquewar · Torquewar

So I'm into some brake line rework etc. Have the master off and was thinking about the bench bleed technique. Done this many times but i have a reverse bleeding system. Basically you pump fluid through the bleeders up into the master . This works great for the standard line clearing but i thought why n...

Windsor · Windsor

hey guys What wiring harness have you guys used or were you happy with? Or not happy with? did you buy it locally? im thinking about the rebel 9+3 harness. what do you think? thanks

supernash · supernash

OK, I know this might take a bit to explain, but anybody that has rebuilt a carb will understand. This is about the Kleen flo Carb and Parts cleaner. I'm talking the stuff that comes in a 5 gallon bucket sealed with a heavy plastic bag when you buy it. I think the last bucket was around $180 or so. I'm thinki...

Roboticist · Roboticist

Hey guys. I am in the midst of buying a donor truck to use the frame for my '52 Mercury build. I'm looking at a 96 Ranger at the moment. I'm also looking at a 1969 Inline 6 to put in the truck. It comes with a 3 speed manual, but I need an automatic (For various reasons). So here's the questions: What transmi...

henrys57wagon · henrys57wagon

Has anyone used Delo Diesel oil by Chevron? It is on sale at Walmart US for 11.28 US. RotellaT is 13/ gal. Both are 15-40. Cosco has Delo 3 gal for 32.99.

South Shore · South Shore

I want to do a thorough cooling system flush on my motor to get all the rust and acumulated crap out of the engine cooling system. The motor is fully assembled SBC sitting in an engine cradle on the floor on casters. It is much easier and far less messy to do it before I put it into the car for sure. Don't want...

henrys57wagon · henrys57wagon

Helping my buddy trying to figure what is the reason for one of his headlights is dim on L/beam and when switched to H/beam the opposite light is dull. The H/beam indicator is on regardless of which position the dimmer is in. There is always power to outside pin of the connector so I'm thinking that the di...

Blu Impala · Blu Impala

I am looking at this air conditioning system for my 67 Impala 2 door hardtop. I have had the car for 37 years and have been keeping it up to date.. The car is riding on a 68 Station Wagon Frame due to the fact the station wagon had disc brakes and the original frame was severely rusted out. The original 283...

Homer · Homer

I am installing a FiTeck 30003 go street EFI system in my 34 which has a 1986 302 mustang motor in it. My problem is that I have put in electronic ignition, what it has to have. they say that I now have to have 12 volts to the distributor and coil as the old ones where not a full 12 volts and there is a resister in...

knuckles · knuckles

Does anyone here or know of anyone that can punch two rows of louvers in a hood? Thanks! Steve

henrys57wagon · henrys57wagon

Here is a front park/ signal light diagram that 2d_willys on the HAMB posted for me. For some reason it will not load here? In the park lamp wire add a 20ohm, 1W resistor and in both wires add a # 1N4001 diode. Use a 1129 or an 81 bulb. -- Edited by henrys57wagon on Friday 18th of November 2016 09:17:04 AM

Bones · Bones

The glass doors on my coupe have started filling up with water from washing. I can't be the first guy having this issue with fiberglass cars and not sure as to why there aren't drain holes drilled. Anyone see a reason not to do this? Or can I just drill a drain hole in the lowest point up under the door and put...

Bones · Bones

Looks like a good place to start . Had this for years. Ran the #s tru Muncie sites but can't come up with anything to confirm if it is or isn't. Any help would be great -- Edited by Bones on Wednesday 2nd of November 2016 12:45:17 AM

ram1976 · ram1976

Hi, I recently purchased the above car with a 440 engine, all were converted to 12v. No issue on driving. I drove the car for almost 2 hrs and stop for gas, could not able to start it again. All the electronics are working. No clicking sound. No spark when I boost the battery, but battery is full charged. S...

Kustoms · Kustoms

Looking at changing my 1930 3 window coupe to suicide doors. Always liked the cool look. I heard the left and right doors fit both sides just swap all the pillars to match the doors. Anyone out there know this before I start taking these apart to test!!

Nickeleye · Nickeleye

I noticed this a few weeks ago. The center of the wheel cracked all over the place. lots more cracks than you can see in the picture too. It had happened at some point over the winter, I can't see anything except the temperature changes causing this??? Any other ideas? Anyways, I contacted the company I b...

123pugsy · 123pugsy

My 76 Chevy with Eaton posi is making a nice grinding, crunching sound at low speeds. Anybody got a guy or is anybody here a guy? Don't have time to clean the garage and don't have time to fix it myself.....damn truck couldn't even wait til I finished the house.. I got a recommendation from Al at Driveline...

Nickeleye · Nickeleye

I've been trying to figure out a problem in the truck but haven't sorted it out yet. It seems like vapor lock. Starts AMAZING when cold. But turn the truck off hot and it'll start up again nice an easy within a minute or two of shutting off but let it sit for 5 minutes or more and it's a difficult start. I insul...

gkent · gkent

Restoring a dash and the plastic bezel needs to be rechromed. I've had experience with having them "vacuum chromed" and the results were less than desirable. I'd like to try the spray chrome this time. Looking for someone kinda local to do it.

72endurawagon · 72endurawagon

i have a wide ratio muncie in my 64 buick wagon behind a well built 455 ,had it out for a ride today,was nice to it ,drove about an hour..came home parked it out front,came time to move it,it seems to be in reverse when in neutral,when i do find a forward gear it lugs down to the point of stalling.emerg brake i...

new member gmc 4x4 · flathead48

Hi All; I have a 89 GMC suburban 4x4 It has 31x10.50 x 15 and 31x11.50 x 15 tires 6x5.5x7 wheels . These tires are hard to find and expensive around my area, that is Tyler Texas. does any one on here know what 16in wheels would fit? I have good 16in tires. I have read Toyota wheels will work. Please emai...

Frank from Hamilton · Frank from Hamilton

Hi, I am new to Rodders and new to the Classic car world. I just bought a 69 Ford LTD and I know absolutely nothing about cars. The car is in really good shape but it now won't start - the entire neighborhood believed it was the Solenoid switch so I was able to change that - but it didn't do anything. So, I th...

flatduck · flatduck

one a 1977 ford ltd like the one in my avatar ............what is easier from inside loosing up the steering colum or under by dropping the idle arm and with a few swear and scratching knucle and getting dirty , also anybody as one to sell ?

Livetodrive · Livetodrive

All, I realized that a lot of my posts are way too serious so I thought I'd share this one. I scored a very nice 15" Woody from some guy on Kijiji today. Its perfect for the Fastback Mustang, but I can't figure out how the airbag wires up?

meester_jamie · meester_jamie

I have a 1966 Marlin .. 4 wheel drums , brake pedal has been trouble for awhile now.. long story ,, everything is new on this car.. or in new condition.. but that doesn't mean it is working fine, and I may have to replace .. but I think it is just a matter of dialing it in.. so,, for some reason... and I can't ima...

72endurawagon · 72endurawagon

I Have a 3 core rad from my 64 buick wagon that needs a new core,was a brand new rad till last nights ride.....just wondering if anyone has any shops they like in london/sarnia area,thanks for any info! Price of 275 to replace rad,never had one recored so not sure of price of that...

Smokin Joe · Smokin Joe

Start protesting Hello folks, Summer recess is always a good time for governments to try to slip unpopular things through and it looks like this summer will be no different. Remember that we got the government to back down of the AMPS proposal and there is no reason that we can’t do the same here i...

supernash · supernash

Anybody have a Campbell Hausfield p/w and still have the parts manual ? This is my Water Wizard 2000. 5 HP Brigs Diamond. The pump went wonky a year or so ago, so I rebuilt it, but I lost the key somehow. The pump slot is 6mm, but the Briggs crank is not, so clearly it's a stepped key. I can't find any info no-wh...

77

Hey all Yeah I know the NastyGirl is a bit late model . The womans 87 trans am w t tops . The car gets so freaking hot inside in the sun . I,m gonna make up two panels to go under t roofs to block sun . Has any one found any window glass application to block u v and heat of the sun thru t roofs or window glass ..Thanks ....

South Shore · South Shore

What rear end ratio would be the best? The car weighs 3400 LBS. loaded, engine is a low horse 240 Hp. stock 327, trany is a TH 350, rear end is a 10 bolt posi., rear tires are 28" dia. Looking for the best all round ratio to use for cruzing not racing.

Smokin Joe · Smokin Joe

Here is one every one should read. Who actually reads the labels on the cans and do you understand what it says???? These warnings are not there for your benefit for my way of thinking but the manufacturers litigation liability's. No different than the adds you see on TV advertising their medicatio...

Undead_Edsel_59 · Undead_Edsel_59

Alright, I've been trying to figure out the idiot lights, in my 66 olds Dynamic. None of them work. The the cold light came on once a a while back. But that was it. I've checked the bulbs. And for broken wires, and made sure sensors where all hooked up. Fuel gauge is in the same panel as the lights, and it work...

Mikey44 · Mikey44

Hey Guys ... I live in Northern Ontario. where would be a good place to order a new transmission from?

two tone 56 · two tone 56

I installed a set of Lokars 1955-57 clutch brake pedal arms a few weeks ago,must say I am very pleased.The installation went well except for their instructions dealing with the brake pedal installation.They wanted to have the pedal and return spring installed while the clutch brake housing was sti...

Homer · Homer

What I would like to do is replace my 68 302 Ford and C4 tranny in my 34 with a up to date fuel ingection 302.Were can I get sizes of engines so that I do not have to do any body work ,just weld in new mounts if possible.

Nickeleye · Nickeleye

Just hoping someone could identify what this brake pedal assembly is out of. Thanks,

Livetodrive · Livetodrive

So the back story to the picture is that myself and my oldest brother flew into Las Vegas, bought a 1968 Charger from a dealer on Freemont street and started driving home to Pickering. Seemed like a great idea until we got across the hoover dam and the 383 quits. I pull the coil wire and crank it over, goo...

Kustoms · Kustoms

Picked up a 30 Chevy 3 window and would like to upgrade the suspension. Didn't want to pay the 4000 for the ifs setups. Whats out there that works, any ideas.

flatduck · flatduck

anybody made a swap on a 56 monarch well I think all 55 56 fords must be the same I want to change from single line to dual without spending the big dollars anyone know of something that will fit from the sixties or 70 s ford ?

hotrod-steve · hotrod-steve

A friend has a 37 Cadillac he wants to clip and Ive heard the Crown Vics seem to be the choice now. Has anyone had any experience with these?

South Shore · South Shore

I have an Overhead Door Co. Touch n Go Model 1000A garage door opener that has worked flawlessly for years. Now it works intermitantly. Seems to work in either direction fine but if you activate it again soon, in either direction after the first activation, it won't completely open or close. Doesn't c...

willys392 · willys392

Hey guys, I'm looking at using a small bearing 9" differential out of a 67 Ford Fairlane (390 car) in my 56 F100. I need new ubolts. Can I use the 3" diameter bolts or do I have to go smaller? The axle tubes narrow down to 2.875" (I think it's 2.875") from the normal 3" dia. thanks Bill

Homer · Homer

I have a IC Dynamics keyless entry model 2RTA my remot will not work but the wifes will, I replaced the battery and still will not work. I called and emailed IC Dynamics and no one got back to me .Does any one know someone who will repair the remote.

V2addict · V2addict

Hi guys, has anyone ever used Evans waterless coolant, I'm wondering if this is worth the extra outlay as it says it never needs to be replaced and won't corrode the cooling system? I do realize its twice the price and not readily available, so extra would need to be stocked. Thank you, Angelo

DavidP · DavidP

I thought it would be a good time to replace the front windshield on my 1954 Caddy ... before I finish putting all the trim back on that I removed to install vintage air last summer ... Its not cracked / chipped or scored ... but I do have a foggy area on the passenger side ... that looks like $#@% ... Looking f...

billyisamountain · billyisamountain

I have a set of 186 heads and noticed that two of the valves had oil visible on the inside of the head. I pulled the springs and noticed that the valve guides are loose and can be rotated by hand. Is there a way to tighten them up or am I looking at having the guides replaced. JG

trans cross member · Marten

So it has been a while since I made any progress but got a chance today. I am building the trans cross member. Thought I would put some pics here so not to confuse my build page. That and I need/would like to know that I am doing it right. First pic is what I started with. If you look on the left you can see...

Roboticist · Roboticist

Hey guys. My truck cab needs some TLC around the windshield area. I'd love to find a sheet metal replacement panel or a donor part which is solid. Does anyone know a place to get a prefab replacement so I don't have to recreate this area of the cab? Thanks!

Marten · Marten

Thinking of putting a winch in my shop to pull the truck in from outside. It is easy to roll out as it is all down hill, getting it back inside is hard. So can someone explain how much pull strength I would need.

Topic		Started By	Replies	Views	Last Post
	Flooring/carpet ? (Preview) Good morning: I should have the floor panels in shortly but wonder where to get the carpeting normally installed in cars? It is very low profile and has a nice trim to it. I'd like to custom fit it if I can find where to get it and how to trim it? Any advice would be appreciated. Thanks to all.	Cuddles	2	1692	Mar 31, 2017 by Cuddles
	Brake bleeding (Preview) So I'm into some brake line rework etc. Have the master off and was thinking about the bench bleed technique. Done this many times but i have a reverse bleeding system. Basically you pump fluid through the bleeders up into the master . This works great for the standard line clearing but i thought why n...	Torquewar	2	1734	Mar 16, 2017 by Torquewar
	Wiring harness (Preview) hey guys What wiring harness have you guys used or were you happy with? Or not happy with? did you buy it locally? im thinking about the rebel 9+3 harness. what do you think? thanks	Windsor	16	2930	Mar 16, 2017 by Bradshaw
	Parts cleaner (Preview) OK, I know this might take a bit to explain, but anybody that has rebuilt a carb will understand. This is about the Kleen flo Carb and Parts cleaner. I'm talking the stuff that comes in a 5 gallon bucket sealed with a heavy plastic bag when you buy it. I think the last bucket was around $180 or so. I'm thinki...	supernash	8	2628	Mar 4, 2017 by gkent
	engine/tranny question (Preview) Hey guys. I am in the midst of buying a donor truck to use the frame for my '52 Mercury build. I'm looking at a 96 Ranger at the moment. I'm also looking at a 1969 Inline 6 to put in the truck. It comes with a 3 speed manual, but I need an automatic (For various reasons). So here's the questions: What transmi...	Roboticist	27	5340	Feb 21, 2017 by Roboticist
	delo vrs rotella (Preview) Has anyone used Delo Diesel oil by Chevron? It is on sale at Walmart US for 11.28 US. RotellaT is 13/ gal. Both are 15-40. Cosco has Delo 3 gal for 32.99.	henrys57wagon	14	4680	Feb 21, 2017 by Gwillyville Kid
	Cooling System Flush (Preview) I want to do a thorough cooling system flush on my motor to get all the rust and acumulated crap out of the engine cooling system. The motor is fully assembled SBC sitting in an engine cradle on the floor on casters. It is much easier and far less messy to do it before I put it into the car for sure. Don't want...	South Shore	8	3344	Feb 21, 2017 by fraso
	99 ram headlight problems (Preview) Helping my buddy trying to figure what is the reason for one of his headlights is dim on L/beam and when switched to H/beam the opposite light is dull. The H/beam indicator is on regardless of which position the dimmer is in. There is always power to outside pin of the connector so I'm thinking that the di...	henrys57wagon	9	2864	Jan 10, 2017 by henrys57wagon
	Considering Classic Auto Air #20-233-3I (Preview) I am looking at this air conditioning system for my 67 Impala 2 door hardtop. I have had the car for 37 years and have been keeping it up to date.. The car is riding on a 68 Station Wagon Frame due to the fact the station wagon had disc brakes and the original frame was severely rusted out. The original 283...	Blu Impala	8	3221	Dec 20, 2016 by slim
	Need help electrical (Preview) I am installing a FiTeck 30003 go street EFI system in my 34 which has a 1986 302 mustang motor in it. My problem is that I have put in electronic ignition, what it has to have. they say that I now have to have 12 volts to the distributor and coil as the old ones where not a full 12 volts and there is a resister in...	Homer	6	2515	Dec 8, 2016 by DJD
	punching Louvers (Preview) Does anyone here or know of anyone that can punch two rows of louvers in a hood? Thanks! Steve	knuckles	2	2128	Nov 29, 2016 by Ground Pounder
	How to wire a single bulb for park/ signal usage (Preview) Here is a front park/ signal light diagram that 2d_willys on the HAMB posted for me. For some reason it will not load here? In the park lamp wire add a 20ohm, 1W resistor and in both wires add a # 1N4001 diode. Use a 1129 or an 81 bulb. -- Edited by henrys57wagon on Friday 18th of November 2016 09:17:04 AM	henrys57wagon	4	1982	Nov 18, 2016 by parklane
	Glass doors filling up with water (Preview) The glass doors on my coupe have started filling up with water from washing. I can't be the first guy having this issue with fiberglass cars and not sure as to why there aren't drain holes drilled. Anyone see a reason not to do this? Or can I just drill a drain hole in the lowest point up under the door and put...	Bones	7	2296	Nov 16, 2016 by Petebil
	Who can help identify this 4 speed More pictures if we need em (Preview) Looks like a good place to start . Had this for years. Ran the #s tru Muncie sites but can't come up with anything to confirm if it is or isn't. Any help would be great -- Edited by Bones on Wednesday 2nd of November 2016 12:45:17 AM	Bones	6	2149	Nov 3, 2016 by Bones
	1951 Packard 400 with 1976 Dodge 440 v8 (Preview) Hi, I recently purchased the above car with a 440 engine, all were converted to 12v. No issue on driving. I drove the car for almost 2 hrs and stop for gas, could not able to start it again. All the electronics are working. No clicking sound. No spark when I boost the battery, but battery is full charged. S...	ram1976	5	2514	Oct 31, 2016 by RacerRick
	Suicide door swap (Preview) Looking at changing my 1930 3 window coupe to suicide doors. Always liked the cool look. I heard the left and right doors fit both sides just swap all the pillars to match the doors. Anyone out there know this before I start taking these apart to test!!	Kustoms	8	2786	Oct 25, 2016 by DJD
	Cracked Steering Wheel (Preview) I noticed this a few weeks ago. The center of the wheel cracked all over the place. lots more cracks than you can see in the picture too. It had happened at some point over the winter, I can't see anything except the temperature changes causing this??? Any other ideas? Anyways, I contacted the company I b...	Nickeleye	10	2457	Oct 17, 2016 by ram1976
	Posi Repair...Who Do You Know? (Preview) My 76 Chevy with Eaton posi is making a nice grinding, crunching sound at low speeds. Anybody got a guy or is anybody here a guy? Don't have time to clean the garage and don't have time to fix it myself.....damn truck couldn't even wait til I finished the house.. I got a recommendation from Al at Driveline...	123pugsy	9	2790	Oct 7, 2016 by Smokin Joe
	Vapor Lock? (Preview) I've been trying to figure out a problem in the truck but haven't sorted it out yet. It seems like vapor lock. Starts AMAZING when cold. But turn the truck off hot and it'll start up again nice an easy within a minute or two of shutting off but let it sit for 5 minutes or more and it's a difficult start. I insul...	Nickeleye	8	2001	Aug 31, 2016 by Nickeleye
	Anyone doing "spray chrome" in south western Ontario (Preview) Restoring a dash and the plastic bezel needs to be rechromed. I've had experience with having them "vacuum chromed" and the results were less than desirable. I'd like to try the spray chrome this time. Looking for someone kinda local to do it.	gkent	5	8990	Aug 24, 2016 by Jeff66
	muncie issues (Preview) i have a wide ratio muncie in my 64 buick wagon behind a well built 455 ,had it out for a ride today,was nice to it ,drove about an hour..came home parked it out front,came time to move it,it seems to be in reverse when in neutral,when i do find a forward gear it lugs down to the point of stalling.emerg brake i...	72endurawagon	7	2004	Aug 24, 2016 by 72endurawagon
	new member gmc 4x4 (Preview) Hi All; I have a 89 GMC suburban 4x4 It has 31x10.50 x 15 and 31x11.50 x 15 tires 6x5.5x7 wheels . These tires are hard to find and expensive around my area, that is Tyler Texas. does any one on here know what 16in wheels would fit? I have good 16in tires. I have read Toyota wheels will work. Please emai...	flathead48	4	1722	Aug 16, 2016 by flathead48
	Good Ford Mechanic in Hamilton? (Preview) Hi, I am new to Rodders and new to the Classic car world. I just bought a 69 Ford LTD and I know absolutely nothing about cars. The car is in really good shape but it now won't start - the entire neighborhood believed it was the Solenoid switch so I was able to change that - but it didn't do anything. So, I th...	Frank from Hamilton	6	2266	Aug 12, 2016 by Frank from Hamilton
	help how to change a rag joint (Preview) one a 1977 ford ltd like the one in my avatar ............what is easier from inside loosing up the steering colum or under by dropping the idle arm and with a few swear and scratching knucle and getting dirty , also anybody as one to sell ?	flatduck	0	1538	Aug 12, 2016 by flatduck
	15" Woody (Preview) All, I realized that a lot of my posts are way too serious so I thought I'd share this one. I scored a very nice 15" Woody from some guy on Kijiji today. Its perfect for the Fastback Mustang, but I can't figure out how the airbag wires up?	Livetodrive	3	6550	Aug 7, 2016 by DJD
	working bugs out of brakes.. may not be a perfect installation . (Preview) I have a 1966 Marlin .. 4 wheel drums , brake pedal has been trouble for awhile now.. long story ,, everything is new on this car.. or in new condition.. but that doesn't mean it is working fine, and I may have to replace .. but I think it is just a matter of dialing it in.. so,, for some reason... and I can't ima...	meester_jamie	19	2862	Jul 22, 2016 by Backfire
	Rad Shop Recommendation? (Preview) I Have a 3 core rad from my 64 buick wagon that needs a new core,was a brand new rad till last nights ride.....just wondering if anyone has any shops they like in london/sarnia area,thanks for any info! Price of 275 to replace rad,never had one recored so not sure of price of that...	72endurawagon	14	2864	Jul 12, 2016 by wuga
	Start complaning (Preview) Start protesting Hello folks, Summer recess is always a good time for governments to try to slip unpopular things through and it looks like this summer will be no different. Remember that we got the government to back down of the AMPS proposal and there is no reason that we can’t do the same here i...	Smokin Joe	1	1948	Jul 8, 2016 by Ground Pounder
	Pressure washer issue (Preview) Anybody have a Campbell Hausfield p/w and still have the parts manual ? This is my Water Wizard 2000. 5 HP Brigs Diamond. The pump went wonky a year or so ago, so I rebuilt it, but I lost the key somehow. The pump slot is 6mm, but the Briggs crank is not, so clearly it's a stepped key. I can't find any info no-wh...	supernash	3	1347	Jul 6, 2016 by henrys57wagon
	Ozone depletion , UV rays and window tint (Preview) Hey all Yeah I know the NastyGirl is a bit late model . The womans 87 trans am w t tops . The car gets so freaking hot inside in the sun . I,m gonna make up two panels to go under t roofs to block sun . Has any one found any window glass application to block u v and heat of the sun thru t roofs or window glass ..Thanks ....	77	4	1469	Jul 5, 2016 by 77
	The right rear end ratio? (Preview) What rear end ratio would be the best? The car weighs 3400 LBS. loaded, engine is a low horse 240 Hp. stock 327, trany is a TH 350, rear end is a 10 bolt posi., rear tires are 28" dia. Looking for the best all round ratio to use for cruzing not racing.	South Shore	20	2359	Jul 2, 2016 by ToddDoyle
	Health & Safety (Preview) Here is one every one should read. Who actually reads the labels on the cans and do you understand what it says???? These warnings are not there for your benefit for my way of thinking but the manufacturers litigation liability's. No different than the adds you see on TV advertising their medicatio...	Smokin Joe	3	1681	Jul 1, 2016 by Ground Pounder
	1966 Dynamic 88 idiot lights. Not working. (Preview) Alright, I've been trying to figure out the idiot lights, in my 66 olds Dynamic. None of them work. The the cold light came on once a a while back. But that was it. I've checked the bulbs. And for broken wires, and made sure sensors where all hooked up. Fuel gauge is in the same panel as the lights, and it work...	Undead_Edsel_59	14	2784	Jun 29, 2016 by Model A Guy
	New Tremec 5 speed (Preview) Hey Guys ... I live in Northern Ontario. where would be a good place to order a new transmission from?	Mikey44	6	1536	Jun 29, 2016 by dualquadpete
	1955-57 Chevrolet Lokar Clutch Brake Pedal assemblies (Preview) I installed a set of Lokars 1955-57 clutch brake pedal arms a few weeks ago,must say I am very pleased.The installation went well except for their instructions dealing with the brake pedal installation.They wanted to have the pedal and return spring installed while the clutch brake housing was sti...	two tone 56	0	1397	Jun 27, 2016 by two tone 56
	Size of Ford 302 (Preview) What I would like to do is replace my 68 302 Ford and C4 tranny in my 34 with a up to date fuel ingection 302.Were can I get sizes of engines so that I do not have to do any body work ,just weld in new mounts if possible.	Homer	2	1229	Jun 22, 2016 by Homer
	Brake Pedal Assembly Id Please (Preview) Just hoping someone could identify what this brake pedal assembly is out of. Thanks,	Nickeleye	4	1215	Jun 13, 2016 by Redneck Rydes
	Lesson To Share (Preview) So the back story to the picture is that myself and my oldest brother flew into Las Vegas, bought a 1968 Charger from a dealer on Freemont street and started driving home to Pickering. Seemed like a great idea until we got across the hoover dam and the 383 quits. I pull the coil wire and crank it over, goo...	Livetodrive	15	1816	Jun 12, 2016 by 69SS454
	Ideas on front suspension 30 chev (Preview) Picked up a 30 Chevy 3 window and would like to upgrade the suspension. Didn't want to pay the 4000 for the ifs setups. Whats out there that works, any ideas.	Kustoms	4	1475	Jun 3, 2016 by slim
	swap from single to dual brake line (Preview) anybody made a swap on a 56 monarch well I think all 55 56 fords must be the same I want to change from single line to dual without spending the big dollars anyone know of something that will fit from the sixties or 70 s ford ?	flatduck	5	1674	May 31, 2016 by Gwillyville Kid
	front end clip (Preview) A friend has a 37 Cadillac he wants to clip and Ive heard the Crown Vics seem to be the choice now. Has anyone had any experience with these?	hotrod-steve	2	1280	May 29, 2016 by RacerRick
	Trouble with a Garage Door Opener. (Preview) I have an Overhead Door Co. Touch n Go Model 1000A garage door opener that has worked flawlessly for years. Now it works intermitantly. Seems to work in either direction fine but if you activate it again soon, in either direction after the first activation, it won't completely open or close. Doesn't c...	South Shore	11	2023	May 24, 2016 by Petebil
	U bolts for Ford small bearing 9" axle (Preview) Hey guys, I'm looking at using a small bearing 9" differential out of a 67 Ford Fairlane (390 car) in my 56 F100. I need new ubolts. Can I use the 3" diameter bolts or do I have to go smaller? The axle tubes narrow down to 2.875" (I think it's 2.875") from the normal 3" dia. thanks Bill	willys392	2	2503	May 14, 2016 by willys392
	Remote keyless entry (Preview) I have a IC Dynamics keyless entry model 2RTA my remot will not work but the wifes will, I replaced the battery and still will not work. I called and emailed IC Dynamics and no one got back to me .Does any one know someone who will repair the remote.	Homer	5	1502	May 14, 2016 by entourageguy
	Coolant (Preview) Hi guys, has anyone ever used Evans waterless coolant, I'm wondering if this is worth the extra outlay as it says it never needs to be replaced and won't corrode the cooling system? I do realize its twice the price and not readily available, so extra would need to be stocked. Thank you, Angelo	V2addict	2	1435	May 12, 2016 by 40Rat
	Looking for recomendations on a glass shop to replace 50's Cadillac windshield ... (Preview) I thought it would be a good time to replace the front windshield on my 1954 Caddy ... before I finish putting all the trim back on that I removed to install vintage air last summer ... Its not cracked / chipped or scored ... but I do have a foggy area on the passenger side ... that looks like $#@% ... Looking f...	DavidP	10	1892	May 12, 2016 by shag766
	loose valve guides (Preview) I have a set of 186 heads and noticed that two of the valves had oil visible on the inside of the head. I pulled the springs and noticed that the valve guides are loose and can be rotated by hand. Is there a way to tighten them up or am I looking at having the guides replaced. JG	billyisamountain	19	2665	Apr 23, 2016 by shag766
	trans cross member (Preview) So it has been a while since I made any progress but got a chance today. I am building the trans cross member. Thought I would put some pics here so not to confuse my build page. That and I need/would like to know that I am doing it right. First pic is what I started with. If you look on the left you can see...	Marten	7	1731	Apr 22, 2016 by Marten
	52 Mercury Truck windshield frame? (Preview) Hey guys. My truck cab needs some TLC around the windshield area. I'd love to find a sheet metal replacement panel or a donor part which is solid. Does anyone know a place to get a prefab replacement so I don't have to recreate this area of the cab? Thanks!	Roboticist	12	1750	Apr 21, 2016 by shag766
	winch strength (Preview) Thinking of putting a winch in my shop to pull the truck in from outside. It is easy to roll out as it is all down hill, getting it back inside is hard. So can someone explain how much pull strength I would need.	Marten	14	2028	Apr 20, 2016 by Cat in the Hat
«First < 1 … 4 5 6 7 8 … 17 > Last» \| Page of 17 sorted by