I had these chrome, pot metal 3D stars on my '37.... about 3"..... I found them on a toolbox at a scrap yard....They had one threaded stud in the center on the back..... I would really like to find some more of them.... Does anyone have any clue what they might be off of? Any help appreciated
Kathleen Wynn, Donald Trump, and VladimirPutin all die and go to hell. Whilethere, they spy a red phone and ask what the phone is for.The devil tells them it is for calling back to Earth.Putin calls Russia and talks for 5 minutes. When he was finished the devil informs him that thecost is a million...
Is there a place on this side of the border to order 'cut to length' axles for a 9" Ford? I need 31 spline axles, I don't need extreme 3000hp duty axles, these are for a hot rod. So I'm cheap and don't want to spend money on something I don't need. Thanks for any direction.
Here is the truck when I bought it in April 2013 OK. Who played smashup derby with these fenders?Would anyone try to bang these out or should I be shopping? The consensus seems to be bang them out over the winter. This was always my plan. A little bit of dirt etc. on the floor, but atleast there is a floo...
it seems I've aquired an old RM250 I'm not a "bike guy" so I'm looking for ways to identify exactly what it is it has duel coil over shocks with reservoirs and an aluminum swing arm most of the ones I'm finding on line are mono shock unlike this old thing from what I've found in a few hours of looking into t...
Tan Leather with seat belts built in to seats/ Front and backs. 100 for all . Air bags both front.. 150.with steering wheel/radio controls on wheel. To be added to a kijiji add.. Complete car was parted out. Many parts available . -- Edited by Ground Pounder on Friday 3rd of February 2017 07:00:4...
Selling a pair of real magnesium wheels, they are Chevrolet bolt pattern 4.75 These are vintage gasser dragster rear wheels. 15x10 NOS Tires included $1500 Can ship but without tires
Well it took about 8 months but I finally am able to see the specialist in early January and I'm expecting the procedure for replacing a bum knee to take place shortly thereafter . Any word of wisdom from those who have had this done already ? Thanks , T
Well. I guess it didn't take too long to get this done... car was down for about 2 weeks. The first turbo I had one was not sized right and didn't produce boost until about 4,000 RPM. I swapped that one out for a more appropriate size and now see full boost at 3,000 RPM. Runs pretty good!
Full load leather 283'000 km Silver sedan No lights on No rust Clean under carriage New alt Good tires New front pads E brake works 3500. Drive it away. -- Edited by Ground Pounder on Tuesday 31st of January 2017 07:33:07 PM
I have a GM 350 torque converter for sale. Brand new. From KingOMatic. Listed as 1969-1979. Nut and bolt installation method. 50 bucks. Attachments View imageView imageView imageView imageView image __________________ PUGSY
Looking for the old school steering wheel wrap. Anyone know a place that still has it? Trying to avoid ebay for this! -- Edited by gkent on Wednesday 14th of December 2016 09:42:51 AM
White oxford exterior Repainted black once . Red oxford blood interior .. 350 /Auto Body off restoration Started Years ago ..Car was put in storage Years ago. Now Pulling car out to finish into rolling Chassis/ Frame was blasted an the rear cross member above diff upgraded professionally [looks fac...
this is my next project growing up listening to dad talk about all the cars hes seen and had i thought this would tickle him pink when i brought home this project probably the roughest anglia ive seen around but was in my budget im impressed at the people ive talked with about this car it wasnt long bef...
I heard this on Tuesday but wanted to get more info on it . My interest in Nascar has gone from watching every race to no races this past year . Carl Edwards was one of my favourite drivers especially when he and Kenseth were at Roush , driving Fords . With Toyota ....not so much . Edwards said that racing c...
So I was talking with some gear heads about "gov. regs" and what we would do if in charge. I hear and read lots of bitching and whining but see no suggestions, so I would be interested in knowing what would you do if there was a clean slate. Make hot rods safe and ban all ratrods doesn't count. Details pleas...
Looking for an oil pan for a 292 Chev inline 6 manufactured from the mid 60s until the mid 80s. Not a 250 oil pan. Stopped at DOM's today and they looked at me like I was from outer space. Proceeded to Bill's, but they had nothing. If you have one to sell or know where I might find one, please speak up. Than...
Preferably someone who specializes in resto work and will "get it done" - not a shop that takes 2 years to do 40 hours of work. 1) will do panel replacement 2) will do custom sheet metal work (smooth firewall, mini-tubs) 3) doesn't pad their hours 4) quality workmanship
looking for some 15" drag radials or maybe even slicks 295/50/15 325/50/15 28/10.50/15 28/11/15 or similar if the slicks are not tubeless i would also need the tubes thanks Ken
I just installed a higher ratio gear set on a newer GM truck, and now the ABS computer is not happy because the transmission VSS is spinning faster than what it's used to. I called GM this morning, but they're telling me that they need to call head office to find out how to fix it. BS if you ask me. I'm sure I'm...
Looking for '53 - '56 Ford F1 brakes.... backing plates, hubs, drums.... Must be in good, usable condition Original or New.... Or just NEW Drums..... Ottawa and surrounding area....or others if willing to ship/transport.
I am looking at a 10' snow blade with no harness that's on kijiji in Mitchell. Its just too far to travel to get it ( 5 hrs 1 way) so was wondering if someone with an empty truck or trailer was coming up my way. I will pay of course!
D2 code block I know nothing about the internals (I believe all stock) Rolls over not seized Chrome valve covers Stock intake to Oil Pan $300 Call or text (519)897-2422
Frame is clean,just been acid dipped. Decent shape,has been cut off behind cab. Do your own back half Call or text 5198972422 First $300 Decided to build custom frame instead. -- Edited by dragstar on Friday 13th of January 2017 05:20:53 PM
Brand new gm #706 LS truck heads -correct for 4.8l/5.3 l -were on 199-2007 gm trucks-new not rebuilt-trade price at gm is $1,489 before taxes---Deal at $450 -may trade for chevelle cowl induction parts or ss rims-posted here before I put on kijiji-thanks in advance. Keep on Cruising!!! Dave
A fellow was selling licence plate covers at the International Centre swap meet. It has been on my mind ever since. He was telling a fellow that the 407 tolls will not be able to read his plate from the way it is designed and says it is no different than any cover on a plate. That is the problem I have with th...
There are a lot of guys building trucks these days and I was wondering if anyone had a front axle or especially the front drum brake setup that they were not using and would like to dispose of at a fair price. I believe 53 to 56 setups were generally the same.ThanksWarren
Helping my buddy trying to figure what is the reason for one of his headlights is dim on L/beam and when switched to H/beam the opposite light is dull. The H/beam indicator is on regardless of which position the dimmer is in. There is always power to outside pin of the connector so I'm thinking that the di...
https://www.youtube.com/watch?v=6dI2BgTdvHA&list=PLz_Amg7Y-DGTLTwyPNaVlGczkBbIB8VR9-- Edited by Ground Pounder on Monday 9th of January 2017 06:56:09 PM
I'm looking to put a s10 5 speed in my 34 ford roadster and was wondering what position is right for the shifter? Is it the one with the shifter close to the case or at the rear of the extention housing? Randy
