I have the opportunity to purchase an original 1957 chevy truck 283 staggered bolt engine. I am interested seen how it would be very neat to have the original engine in my truck. I have read that the staggered bolt engines are the 265 bored out to 283 and are known for overheating because of how thin the wa...
sad sights for sure but some good pickins if ya knew where they were the roached cobra daytona blew my mind considering the millions of $$$ it's worth to bad there was only a partial pic of it https://www.youtube.com/watch?v=aILyrUo_Edo
I'm looking for a set of ford 302 motor mounts. My engine is an early 80's carbed 5.0. I had planned on installing my engine and tranny this past weekend into a project mustang, unfortunately someone has walked off with my motor mounts! At least they were nice enough to leave the bolts sitting on the flo...
1960 rear impala or elcamino rear three piece bumper, decent driver quality 100 dollars 1959 front impala bumper, straight, one rust spot with frame support, one piece 125 dollars front 59 winshield, small crack at bottom , probably hidden by rubber seal, free small block fan shroud, has had som...
I am looking for one ALCOA Aluminum Piston for my 261 Chevy I-6. It is marked (cast) inside the skirt ALCOA, LO-EX, and 1159. It is stamped 1766 and 030 on top. I could use a 030 or larger if anybody has one. Any info on these pistons would be appreciated. Need you help on this one. Thank you.
Trying to find a Mechanic around Barrie/New Market area that's good with setting up Stromberg 97's I have a 3x2 setup with progressive linkage on a small block chev. I can trailer the car just about anywhere in the area but not that many guys have experience with 97's. Anyone know someone good that they...
I have a set of 1935-36 ford spindles for sale. Recently mediaBlasted Asking $60 email info@fynrydcustoms.com Thanks, Ryan. -- Edited by FYN RYD Customs on Sunday 14th of September 2014 05:06:40 PM
I have a 1200 sq.ft. shop as well as a 800 sq.ft. thermal pane green house. I heat each very successfully with a big Maxx 80K BTU suspended heater. I just noticed that TSC have these heaters on special for $600 this week. If you are looking for a way to heat your work space, I highly recommend this unit. ...
This is not my car, I have no interest or knowledge of it other than it is for sale in beautiful downtown Stroud. Thought someone might be interested. The paint is a little faded, a bit of surface rust on the painted part of the wheels, dual exhaust, black interior. Very nice presentable car.
Selling for a friend-4 steel wire wheels off of a 50's Buick. Price is $100.00 firm, including 4 tubes. These wires look great on customs or rods. They are 15 inches by 6.5 and 5 on 5 bolt pattern. They are painted, but could be re-chromed. Contact me at jmccarrol@hotmail.com or phone 705-728-849...
Hi all, A friend of my wife and I is looking for a nice runner. 1960's anything, 2 or 4 door. Clean and solid. If you have something you'd like to show me please message me with the details. This woman lost her husband recently and just wants a nice older car to take for drives, for her son to learn basic mech...
I was browsing the Canada Customs sight and noticed that they are refusing to allow any modified vehicles or kit cars into the country. I know the bike guys are having trouble getting trike conversions registered here . Anyone know anything about this?
Complete 1933 Chev coupe dash board. I have repaired and painted it (base/clear). Nice piece for the garage, shop, rec. room, man cave. $250.00 pm if interested. Thanks.
Following is the link to the upcoming 2nd annual Concours Car Show held Sept 13 & 14 at Cobble Beach just North of Owen Sound. This will be a one of a kind display of some of the best cars in North America. The setting is awesome. The proceeds go to support the new helicopter pad at Sunnybrock Hospit...
October 2014 issue of Street Rodder magazine has a very good personal history story on Jeff Norwell. (Who is a member on this site) A good read and a worth while look at one of the industries top illustrators. Also, a bonus to this story....there is a part 2. The saga continues......
Hopefully without the huge Heaney debate (LoL) who's going this weekend? Vending or just visiting. If the weatherman is even close to being right (which he hasn't been for weeks!) it looks like the weekend should be nice anyway.
Hi Ontario rodders, I have been into cars and motorcycles since i was old enough to earn my own money. Well, it started earlier. Have been to dragraces since i was a little kid, and always reading hotrod magz when the other kids had Donald Duck. For the moment I own a Harley that i built myself, a Fiat 600 d...
I took my 63 max wedge to the A&W cruise tonight. I arrived early had my donation ready for the cruise and when I made it the guy said "Were you here at the last one?" I nodded so he took back the draw ticket he was offering and told the guy not to give me a plaque. The big wedge was not happy from...
For sale, a Quarter Master light weight racing flywheel. This is a 130 tooth, 10.4" clutch size, 14 lbs., 6 hole flywheel with an overall diameter of 13 1/4" that is in excellent condition. The flywheel available is priced at $200. This flywheel is neutral balanced but balance pads are a...
The Lone Ranger and Tonto went camping in the desert. After they got their tent all set up, both men fell sound asleep. Some hours later, Tonto wakes the Lone Ranger and says, 'Kemo Sabe, look towards sky, what you see? 'The Lone Ranger replies, 'I see millions of stars.' What that tell you?' asked Ton...
Subject: MARITAL MISUNDERSTANDING
MISUNDERSTANDING??
How men and women record things in their diaries.
Wife's Diary:
Tonight, I thought my husband was acting weird. We had made plans to meet at a nice restaurant for dinner.
I was shopping with my friends all day long, so I thought he wa...
should be a big show tonight with Ideal Supply giving prizes and I believe food also available, located on #121 just south of Haliburton (this was previously scheduled but got rained out)
I have a new starter used a couple of times to run my car in the beginning, but I needed to change to a gear reduction for the engine I have. $60.00. PM me. -- Edited by hotroddonnie on Friday 5th of September 2014 11:52:32 PM
Hi Fellas!Some of you are familiar with my metal shaping and fab work on the sports car we're currently building from scratch. A while ago a suggestion was made to post on Ontario Rodders some of the illustrations and graphic design stuff that I also delve into as well. It’s pretty clear that I love ca...
304 engine with new plugs redone starter and some chrome headers amc 20 complete rear end non posi non tilt but complete steering column asking 400 for everything call or text 9053759441
