Tech

supernash · 77

any leads ? all the conversion kits i ca see are just two speeds

Cuddles · Cuddles

I may have asked this before (I'll write the answer down this time) but what oil is best for summer driving? I researched and discovered that Rotella T & Delvac 1300 have zinc in them and that's good for older engines (I think). Does it matter if they sit in the cold all winter ? I'm changing the oil in S...

Livetodrive · Livetodrive

Happy New Year all! I've been noticing an unusual trend lately, wondering if Covid may be a factor. Seems like I'm getting an unusually high number of complaints about "differential noise". Once I get them opened up, there is always some moisture in the diff case, possibly from condensation? I'...

toomuchjunk · toomuchjunk

Well I'm finished spending large amounts of money on paint jobs. I have decided in the future any cars I buy will have to have a decent look to it body wise. By that I mean no body work on the outside of the body required to drive it the "barn fresh" look. I stumbled on to this. Check out both video's. They kind...

Cuddles · Cuddles

I wasn't sure how I'd go about attaching the Hang Ten dimmer switch pedal to my throttle pedal and then one morning recently, it jus came to me. So for anybody out there wanting to make a spoon pedal more comfortable for your foot, here is what I did: I took a nut that was a bit too big to fit into the back of the...

Cuddles · Cuddles

I am hoping to work out a lot of little 'kinks' whenever the weather allows or at least in the spring. One issue is my doors. When I first got my model A Tudor on the road, the doors used to swing open all the time. Then my 94 year old friend and neighbour from down the road who used to own a few of these in his ti...

77

Hey all so Im just playing around with The Little Gremlin , keep calm its my drag car LOL Apparantly my dollar store battery tender gave out . Battery could have been dead a year to 6 months ?? Could it be recharged ?? . I,m thinking just to put a cheap parts source regular battery in to see if it will start...

Cuddles · Cuddles

I recently started charging my 6 volt & thought I better check fluid levels. It was way down in all 3 cylinders. (half empty) I had saved water from a dehumidifier in two empty lemonade bottles. I understand water from dehumidifiers is ok for a battery. So I topped up the battery but when almost f...

Cuddles · Cuddles

I need to remove a split cotter pin from a hole which has access from only one end. Any tips ? I figure I might be able to drill it out but I think that would be a last measure.

Cuddles · Cuddles

I just watched this video. He ran the wires through metal tubes (I think) and I was told to keep my spark plug wires away from metal or they will arc. Maybe the tubes he slides them through look like metal but they are plastic ?

Cuddles · Cuddles

Opinions ? I love it !

Livetodrive · Livetodrive

Customer complaint was the car would only run if you kept spraying "quick start" in the carb. Claims he does not use ethanol fuels. This is what the o-ring on the needle/seat looks like on his Holley 4160. It degraded so much it actually plugged the path for the fuel to get into the front bowl. The bra...

Cuddles · Cuddles

https://www.youtube.com/watch?v=JLKp81y-tPQ&list=RDCMUCU4f0UCOfiB32Lo4Z6NDghA&index=2

Cuddles · Cuddles

Canadian Tire sells a battery charger for $40.99 that will charge a 6 volt battery. But I read in one of the reviews that it is only good for an 80 amp hour battery (whatever that means). I have a 6 volt battery from NAPA I took out of my 42 truck for winter. Does anyone know if I can use that Canadian Tire cha...

Cuddles · Cuddles

I'm thinking about getting 4 or 5 vintage steel rims sandblasted. Does anyone have a ballpark cost or where to get it done ? Thank you in advance (in case I forget).

supernash · supernash

Guys, I found a box full of plugs. Maybe 100'ish brand new in the boxes. No Idea why I'd have so many of same. Anyway, they are Motomaster TRS79 V-groove. I've tried every cross reference I can find and can't figure out what their for or even convert to AC or NGK. Yes I have new glasses. Harry, you got better...

Livetodrive · Livetodrive

I know I've gone off on this before but it really grinds my gears when I see people spend good money for poor quality parts. Recently had a customer, who is also an old friend, reach out because the new "crate" 454 engine he installed in his project 1970 El Camino was running really bad. As with most of us...

Cuddles · Cuddles

Does anyone have any images of what framework goes beneath a track-T radiator shell ? Is there some kind of framework for support ? Is there bracing of any kind ? Or does the shell just bolt to the frame and / or radiator support ? Thank you.

DJD · DJD

a saved link I found cleaning junk outta my computer https://www.performancetrucks.net/forums/gm-engine-exhaust-performance-21/how-build-exhaust-resonator-tube-eliminate-drone-489463/page4/ [URL]https://www.performancetrucks.net/forums/gm-engine-exhaust-perfor...

Cuddles · Cuddles

I managed to weld the bottom and side panels together and I think the next step is to attach the two compound curves to the side panels but that's a problem. The side panels curve inward from side to side and the compound curve panels curve inward from top to bottom with no curvature sideways. For a final...

Redneck Rydes · Redneck Rydes

I just bought a old International W4 tractor, and it not been run in about 10 years,I have got the gas tank off and there is some nasty crud in there,mostly some rusty gunk,any suggetions that would be the best way to clean it out,it does have a baffle welded tight in the middle,so putting nuts,bolts or a c...

iron horse · iron horse

I just wanted to put this out there to see what everyone thinks. I usually change my own oil and for my whole life, I have used nothing but Fram oil filters and I have never had an issue. Now I understand, from youtube I think, that Fram is probably the worst filter on the market. Just wondering what everyon...

Cuddles · Cuddles

I have a 42 Ford pickup with a mount for the spare tire on the side but the holes in the rim don't line up with the holes in the mount. I thought there must be a bracket missing but the previous owner said there isn't. I don't know how to mount the spare rim and I can't find a video on youtube for a truck this old....

Cuddles · Cuddles

I was having trouble getting my Strombergs set. There is a small hole in the primary arm for the set screw to hit the small hole in the brass rod that controls fuel flow in the primary carburetor. The problem I'm having is that if I use that setting, my primary arm doesn't sit at 45 degrees. It sits almos...

Cuddles · Cuddles

I spent yesterday in the garage making a sheet metal bender. I found a few youtube videos that showed how but this one worked well for me. Hope to finish it up today. Looks like it stores away easy when done. So if anyone needs to make one, here is the link: https://www.youtube.com/watch?v=2iFVW753...

Cuddles · Cuddles

Does anyone know if Lokar makes a short shift kit ? I looked at their site but couldn't sort it out. I have a C4 automatic transmission. Perhaps a different make of short shift kit would be good ?

51 Styline · 51 Styline

I need to put a neutral safety switch in my 51. Its got a 350 auto tranny . is there a factory switch i can adapt to hook it up. With the borders closed it seems the US is out. I am using a Lokar shifter . I seem to remember years ago , when i worked at a GM dealership that the Chevettes had a switch i think woukd w...

classsic · classsic

My 1981 chev truck speedo is in miles per hour and when I'm driving 50 MPH the speedo shows 75 MPH. That's 50 per cent increase! This does not concern me because I'm sure someone changed the rear end previously and I can calculate the kilometers per hour speed from the tach. My question is will the mileag...

supernash · supernash

Had these for years, the one way valve for PCV that ya weld into the collectors. Forget what ya call them. I'm gonna dry fit the headers back in after I remove the solid motor and trans mounts and go back to rubber. With the headers back in, I'll know where I have the clearance down there, which way to point t...

Cuddles · Cuddles

I bought some timing tape for my harmonic balancer so I have to clean my balancer. I need a larger socket to fit the bolt so I can turn my balancer but I don't know what size socket to buy. I have a 66 289 Mustang motor. The biggest I have is 22mm and I know that's too small.

classsic · classsic

my 1981 Chev pickup has a four speed transmission with fourth gear being overdrive. Apparently it is a version of the Chrysler A833 transmission used by GM as a MY 6. It will not go into reverse! Anyone have any experience with this tranny?

jarvis1 · jarvis1

I have a 1980 El Camino that is very rusty. It has power windows. I would like to have these power windows in my 1987 El Camino that has manual windows. My question is, are all cars wired for power windows? Would there be a junction block/plug somewhere in the '87 that I can hook the power window wiring into...

Cuddles · Cuddles

For anyone like myself who is relatively new to this hobby, this is what a burnt valve looks like. When we discovered compression was low in one cylinder, my friend Bill spritzed the headers and found the water didn't evaporate nearly as fast on one header pipe. Sure enough, it was exactly as he predi...

Cuddles · Cuddles

Can anyone please suggest a youtube video that will show me how to properly remove cylinder heads from a 66 289 ? Or even provide step by step instruction without a video ? Thank you. I found two vids but in the first by Thunderhead289, he drops the push rods ( I think they are called ) all over the place w...

Livetodrive · Livetodrive

So, one of my long time customers calls me, he has a 2015 Ram with the 5.7 Hemi and he is getting a "low oil pressure code and CEL on". He took it in to the dealer and they changed the sending unit but the light came back on the next day. He mentioned to me that the oil change was done a couple of weeks ago so I was...

Cuddles · Cuddles

My friend with the 46 Chevy pickup wants to set his motor aside until he can get the mounts and stuff set up on the frame. Does he have to buy an engine stand or can he set it on a pallet with blocks or something ? Stupid question ? I am just trying to save him a few bucks as he puts his ride together. Thank you.

Cuddles · Cuddles

I am looking forward to practicing my welding come Spring. I understand salvage yards are the best place to buy cheap but I only have scrap yards near me. Can anyone tell me where they get metal cheap between Toronto and Ottawa ? Thank you.

Cuddles · Cuddles

My friend with the 46 Chevy pick up is worried about the cost of a potential rebuild on an old 292. The motor sat for years in a combine and then another 10 years in a barn. He thinks it might need a rebuild and wonders about where to take it and what it might cost and if it even needs a rebuild. Any guidance w...

parklane · parklane

Like the caption says, looking for a 58 Edsel Pacer or Ranger 2 door hardtop or coupe. No rust buckets or trailer queen. Just a nice driver. Thanks John

Cuddles · Cuddles

My grocery getter ( I love the term ) suddenly reverted to manual steering on a wickedly cold day so I went to Honda and bought Honda power steering fluid and poured in almost a full bottle. My reservoir was almost empty. So then I drove it out of the drive and back again but still no power steering (and bo...

Cuddles · Cuddles

It just occurred to me this morning that I could build my own frame now and start from scratch. I could rebuild my ride and do it all the way I now know is best. Cool. So has anyone here built their own frame with tubing? A few basic questions: Do I have to have a jig to ensure the finished item is square and...

Livetodrive · Livetodrive

Has anyone ever actually used the "balance" setting in their car stereo? In all the years I've had a car the only time I've adjusted it is when it got nudged doing something else.

Cuddles · Cuddles

If anyone fairly new to the hobby isn't familiar with the Iron Trap Garage youtube videos hosted by a gentleman named Matt (Murray I think), here is a good place to start. In this video Matt shows how to form a sub frame on a model 'A'. Matt is also in a lot of 'Eastwood' videos on youtube and that was how I g...

Cuddles · Cuddles

Today I saw a video of a rat rod with altered suspension and I'm curious to know if anyone here would know how this suspension works. It looks like a nice alternative to bags. The 1932 Ford pick up is called Hemrod and owned by Robert Wong. It has a 392 Hemi but here's the tricky bit. The rear suspension ra...

Cuddles · Cuddles

I emptied my rad so I could get a leak repaired. In the Spring, I am removing a head to have a burnt valve repaired so I thought I'd leave the engine free of coolant since I am going to have to drain it again in the Spring anyway. I just need someone here to reassure me that it is ok to leave the antifreeze out o...

Cuddles · Cuddles

My daily driver is a 2008 Honda Ridgeline. I left it with a friend to do the rear brakes for me since I am still learning how. Anyway, when the job was done, I got the truck home and when I went to lock it up, I discovered my security system / key fob no longer functioned. I imagine the timing is just a coinci...

Marten · Marten

Here is a picture of my A/C and alternator and power steering. The belts in the picture are wrong, it was to check and see if it looked right. I am wondering what is the best way to have the belts.Option # 1 one belt goes from the A/C to the crank to the water pump and back to the A/C. That is the line of groove...

Cuddles · Cuddles

If anyone is starting a project on a channeled model A Tudor and wondering where to store the battery, I looked all around under there and it seems to me that the only place to hide a full size battery is behind the passenger or driver seats under the floor. Especially if you plan to bag your ride and need a...

Rockhauler · Rockhauler

Hi started looking for something to help slow the cracking of dash pads and tires, etc. In my search came across this product called 303 Aerospace Protectant on Amazon but its not cheap and as always the reviews are mixed. Thought I'd ask and see what others are using. Paul

TIREDIRN · TIREDIRN

Interested if anyone is playing music in their hot rod with an ipod, no radio. Thanks -- Edited by TIREDIRN on Saturday 24th of October 2020 02:04:58 PM

Topic		Started By	Replies	Views	Last Post
	Pulse electric wipers kits for 50 chev truck (Preview) any leads ? all the conversion kits i ca see are just two speeds	77	8	691	Feb 6, 2022 by supernash
	summer oil for a 66 289 cu. in. (Preview) I may have asked this before (I'll write the answer down this time) but what oil is best for summer driving? I researched and discovered that Rotella T & Delvac 1300 have zinc in them and that's good for older engines (I think). Does it matter if they sit in the cold all winter ? I'm changing the oil in S...	Cuddles	16	937	Jan 25, 2022 by shag766
	New Trend? (Preview) Happy New Year all! I've been noticing an unusual trend lately, wondering if Covid may be a factor. Seems like I'm getting an unusually high number of complaints about "differential noise". Once I get them opened up, there is always some moisture in the diff case, possibly from condensation? I'...	Livetodrive	11	1193	Jan 11, 2022 by Chris Stapley
	Poppy's (Preview) Well I'm finished spending large amounts of money on paint jobs. I have decided in the future any cars I buy will have to have a decent look to it body wise. By that I mean no body work on the outside of the body required to drive it the "barn fresh" look. I stumbled on to this. Check out both video's. They kind...	toomuchjunk	0	700	Jan 2, 2022 by toomuchjunk
	spoon pedal throttle option (Preview) I wasn't sure how I'd go about attaching the Hang Ten dimmer switch pedal to my throttle pedal and then one morning recently, it jus came to me. So for anybody out there wanting to make a spoon pedal more comfortable for your foot, here is what I did: I took a nut that was a bit too big to fit into the back of the...	Cuddles	14	545	Dec 29, 2021 by Cuddles
	model A doors stick (Preview) I am hoping to work out a lot of little 'kinks' whenever the weather allows or at least in the spring. One issue is my doors. When I first got my model A Tudor on the road, the doors used to swing open all the time. Then my 94 year old friend and neighbour from down the road who used to own a few of these in his ti...	Cuddles	2	497	Dec 29, 2021 by Cuddles
	Re Charging Optima gell cell style battery (Preview) Hey all so Im just playing around with The Little Gremlin , keep calm its my drag car LOL Apparantly my dollar store battery tender gave out . Battery could have been dead a year to 6 months ?? Could it be recharged ?? . I,m thinking just to put a cheap parts source regular battery in to see if it will start...	77	2	462	Dec 21, 2021 by 77
	battery maintenance (Preview) I recently started charging my 6 volt & thought I better check fluid levels. It was way down in all 3 cylinders. (half empty) I had saved water from a dehumidifier in two empty lemonade bottles. I understand water from dehumidifiers is ok for a battery. So I topped up the battery but when almost f...	Cuddles	16	934	Dec 20, 2021 by Cuddles
	split cotter pin (Preview) I need to remove a split cotter pin from a hole which has access from only one end. Any tips ? I figure I might be able to drill it out but I think that would be a last measure.	Cuddles	13	1637	Dec 18, 2021 by poncho62
	spark plug wires (Preview) I just watched this video. He ran the wires through metal tubes (I think) and I was told to keep my spark plug wires away from metal or they will arc. Maybe the tubes he slides them through look like metal but they are plastic ?	Cuddles	5	700	Dec 16, 2021 by Livetodrive
	turnbuckle suspension (Preview) Opinions ? I love it !	Cuddles	0	539	Dec 12, 2021 by Cuddles
	Whats In The Fuel? (Preview) Customer complaint was the car would only run if you kept spraying "quick start" in the carb. Claims he does not use ethanol fuels. This is what the o-ring on the needle/seat looks like on his Holley 4160. It degraded so much it actually plugged the path for the fuel to get into the front bowl. The bra...	Livetodrive	14	633	Dec 5, 2021 by Livetodrive
	metal shaping tips (Preview) https://www.youtube.com/watch?v=JLKp81y-tPQ&list=RDCMUCU4f0UCOfiB32Lo4Z6NDghA&index=2	Cuddles	4	1033	Dec 1, 2021 by 123pugsy
	battery chargers (Preview) Canadian Tire sells a battery charger for $40.99 that will charge a 6 volt battery. But I read in one of the reviews that it is only good for an 80 amp hour battery (whatever that means). I have a 6 volt battery from NAPA I took out of my 42 truck for winter. Does anyone know if I can use that Canadian Tire cha...	Cuddles	2	484	Nov 21, 2021 by Cuddles
	sandblasting (Preview) I'm thinking about getting 4 or 5 vintage steel rims sandblasted. Does anyone have a ballpark cost or where to get it done ? Thank you in advance (in case I forget).	Cuddles	28	1368	Nov 19, 2021 by shag766
	Odd ball spark plugs (Preview) Guys, I found a box full of plugs. Maybe 100'ish brand new in the boxes. No Idea why I'd have so many of same. Anyway, they are Motomaster TRS79 V-groove. I've tried every cross reference I can find and can't figure out what their for or even convert to AC or NGK. Yes I have new glasses. Harry, you got better...	supernash	9	802	Nov 14, 2021 by supernash
	Part Quality (Preview) I know I've gone off on this before but it really grinds my gears when I see people spend good money for poor quality parts. Recently had a customer, who is also an old friend, reach out because the new "crate" 454 engine he installed in his project 1970 El Camino was running really bad. As with most of us...	Livetodrive	6	653	Sep 12, 2021 by Livetodrive
	When that day finally comes (Preview) Does anyone have any images of what framework goes beneath a track-T radiator shell ? Is there some kind of framework for support ? Is there bracing of any kind ? Or does the shell just bolt to the frame and / or radiator support ? Thank you.	Cuddles	0	512	Aug 28, 2021 by Cuddles
	solve exhaust drone. (Preview) a saved link I found cleaning junk outta my computer https://www.performancetrucks.net/forums/gm-engine-exhaust-performance-21/how-build-exhaust-resonator-tube-eliminate-drone-489463/page4/ [URL]https://www.performancetrucks.net/forums/gm-engine-exhaust-perfor...	DJD	3	471	Aug 27, 2021 by 123pugsy
	track T rad shell (Preview) I managed to weld the bottom and side panels together and I think the next step is to attach the two compound curves to the side panels but that's a problem. The side panels curve inward from side to side and the compound curve panels curve inward from top to bottom with no curvature sideways. For a final...	Cuddles	17	968	Aug 24, 2021 by Cuddles
	Cleaning a rusty gas tank (Preview) I just bought a old International W4 tractor, and it not been run in about 10 years,I have got the gas tank off and there is some nasty crud in there,mostly some rusty gunk,any suggetions that would be the best way to clean it out,it does have a baffle welded tight in the middle,so putting nuts,bolts or a c...	Redneck Rydes	14	875	Aug 14, 2021 by Redneck Rydes
	Oil Filters (Preview) I just wanted to put this out there to see what everyone thinks. I usually change my own oil and for my whole life, I have used nothing but Fram oil filters and I have never had an issue. Now I understand, from youtube I think, that Fram is probably the worst filter on the market. Just wondering what everyon...	iron horse	24	1133	Aug 8, 2021 by 77
	spare tire mounting (Preview) I have a 42 Ford pickup with a mount for the spare tire on the side but the holes in the rim don't line up with the holes in the mount. I thought there must be a bracket missing but the previous owner said there isn't. I don't know how to mount the spare rim and I can't find a video on youtube for a truck this old....	Cuddles	6	568	Jul 29, 2021 by Cuddles
	Stromberg 97s (Preview) I was having trouble getting my Strombergs set. There is a small hole in the primary arm for the set screw to hit the small hole in the brass rod that controls fuel flow in the primary carburetor. The problem I'm having is that if I use that setting, my primary arm doesn't sit at 45 degrees. It sits almos...	Cuddles	0	575	Jun 18, 2021 by Cuddles
	sheet metal bending (Preview) I spent yesterday in the garage making a sheet metal bender. I found a few youtube videos that showed how but this one worked well for me. Hope to finish it up today. Looks like it stores away easy when done. So if anyone needs to make one, here is the link: https://www.youtube.com/watch?v=2iFVW753...	Cuddles	8	1020	Jun 16, 2021 by Chris Stapley
	short shift kit (Preview) Does anyone know if Lokar makes a short shift kit ? I looked at their site but couldn't sort it out. I have a C4 automatic transmission. Perhaps a different make of short shift kit would be good ?	Cuddles	2	686	May 19, 2021 by Cuddles
	Neutral Safety Switch (Preview) I need to put a neutral safety switch in my 51. Its got a 350 auto tranny . is there a factory switch i can adapt to hook it up. With the borders closed it seems the US is out. I am using a Lokar shifter . I seem to remember years ago , when i worked at a GM dealership that the Chevettes had a switch i think woukd w...	51 Styline	5	770	May 8, 2021 by Chris Stapley
	speedometer question (Preview) My 1981 chev truck speedo is in miles per hour and when I'm driving 50 MPH the speedo shows 75 MPH. That's 50 per cent increase! This does not concern me because I'm sure someone changed the rear end previously and I can calculate the kilometers per hour speed from the tach. My question is will the mileag...	classsic	7	748	May 7, 2021 by supernash
	PCV valves in the headers (Preview) Had these for years, the one way valve for PCV that ya weld into the collectors. Forget what ya call them. I'm gonna dry fit the headers back in after I remove the solid motor and trans mounts and go back to rubber. With the headers back in, I'll know where I have the clearance down there, which way to point t...	supernash	10	836	May 5, 2021 by Bob T
	harmonic balancer bolt size ? (Preview) I bought some timing tape for my harmonic balancer so I have to clean my balancer. I need a larger socket to fit the bolt so I can turn my balancer but I don't know what size socket to buy. I have a 66 289 Mustang motor. The biggest I have is 22mm and I know that's too small.	Cuddles	10	682	May 5, 2021 by Cuddles
	no reverse (Preview) my 1981 Chev pickup has a four speed transmission with fourth gear being overdrive. Apparently it is a version of the Chrysler A833 transmission used by GM as a MY 6. It will not go into reverse! Anyone have any experience with this tranny?	classsic	4	807	Apr 18, 2021 by classsic
	power window wiring (Preview) I have a 1980 El Camino that is very rusty. It has power windows. I would like to have these power windows in my 1987 El Camino that has manual windows. My question is, are all cars wired for power windows? Would there be a junction block/plug somewhere in the '87 that I can hook the power window wiring into...	jarvis1	9	773	Apr 9, 2021 by DJD
	burnt valve (Preview) For anyone like myself who is relatively new to this hobby, this is what a burnt valve looks like. When we discovered compression was low in one cylinder, my friend Bill spritzed the headers and found the water didn't evaporate nearly as fast on one header pipe. Sure enough, it was exactly as he predi...	Cuddles	4	772	Apr 7, 2021 by Cuddles
	removing heads (Preview) Can anyone please suggest a youtube video that will show me how to properly remove cylinder heads from a 66 289 ? Or even provide step by step instruction without a video ? Thank you. I found two vids but in the first by Thunderhead289, he drops the push rods ( I think they are called ) all over the place w...	Cuddles	40	1612	Apr 5, 2021 by Cuddles
	More Defective Parts (Preview) So, one of my long time customers calls me, he has a 2015 Ram with the 5.7 Hemi and he is getting a "low oil pressure code and CEL on". He took it in to the dealer and they changed the sending unit but the light came back on the next day. He mentioned to me that the oil change was done a couple of weeks ago so I was...	Livetodrive	9	975	Mar 8, 2021 by Livetodrive
	motor storage (Preview) My friend with the 46 Chevy pickup wants to set his motor aside until he can get the mounts and stuff set up on the frame. Does he have to buy an engine stand or can he set it on a pallet with blocks or something ? Stupid question ? I am just trying to save him a few bucks as he puts his ride together. Thank you.	Cuddles	9	714	Mar 3, 2021 by Cuddles
	buying metal (Preview) I am looking forward to practicing my welding come Spring. I understand salvage yards are the best place to buy cheap but I only have scrap yards near me. Can anyone tell me where they get metal cheap between Toronto and Ottawa ? Thank you.	Cuddles	26	1606	Mar 1, 2021 by Cuddles
	292 rebuild (Preview) My friend with the 46 Chevy pick up is worried about the cost of a potential rebuild on an old 292. The motor sat for years in a combine and then another 10 years in a barn. He thinks it might need a rebuild and wonders about where to take it and what it might cost and if it even needs a rebuild. Any guidance w...	Cuddles	2	608	Feb 23, 2021 by Cuddles
	LOOKING FOR A 58 EDSEL (Preview) Like the caption says, looking for a 58 Edsel Pacer or Ranger 2 door hardtop or coupe. No rust buckets or trailer queen. Just a nice driver. Thanks John	parklane	0	525	Feb 21, 2021 by parklane
	Power steering (Preview) My grocery getter ( I love the term ) suddenly reverted to manual steering on a wickedly cold day so I went to Honda and bought Honda power steering fluid and poured in almost a full bottle. My reservoir was almost empty. So then I drove it out of the drive and back again but still no power steering (and bo...	Cuddles	11	710	Feb 21, 2021 by Cuddles
	It just occurred to me (Preview) It just occurred to me this morning that I could build my own frame now and start from scratch. I could rebuild my ride and do it all the way I now know is best. Cool. So has anyone here built their own frame with tubing? A few basic questions: Do I have to have a jig to ensure the finished item is square and...	Cuddles	39	1454	Feb 7, 2021 by Cuddles
	Be Honest (Preview) Has anyone ever actually used the "balance" setting in their car stereo? In all the years I've had a car the only time I've adjusted it is when it got nudged doing something else.	Livetodrive	10	848	Jan 29, 2021 by flatblack55delivery
	learning more stuff (Preview) If anyone fairly new to the hobby isn't familiar with the Iron Trap Garage youtube videos hosted by a gentleman named Matt (Murray I think), here is a good place to start. In this video Matt shows how to form a sub frame on a model 'A'. Matt is also in a lot of 'Eastwood' videos on youtube and that was how I g...	Cuddles	0	524	Jan 27, 2021 by Cuddles
	A real puzzle for most I think (Preview) Today I saw a video of a rat rod with altered suspension and I'm curious to know if anyone here would know how this suspension works. It looks like a nice alternative to bags. The 1932 Ford pick up is called Hemrod and owned by Robert Wong. It has a 392 Hemi but here's the tricky bit. The rear suspension ra...	Cuddles	11	1177	Dec 28, 2020 by Cuddles
	I just want to be certain (Preview) I emptied my rad so I could get a leak repaired. In the Spring, I am removing a head to have a burnt valve repaired so I thought I'd leave the engine free of coolant since I am going to have to drain it again in the Spring anyway. I just need someone here to reassure me that it is ok to leave the antifreeze out o...	Cuddles	10	713	Dec 26, 2020 by Cuddles
	Grocery getter giving a problem (Preview) My daily driver is a 2008 Honda Ridgeline. I left it with a friend to do the rear brakes for me since I am still learning how. Anyway, when the job was done, I got the truck home and when I went to lock it up, I discovered my security system / key fob no longer functioned. I imagine the timing is just a coinci...	Cuddles	7	817	Nov 24, 2020 by Cuddles
	belts and pulleys (Preview) Here is a picture of my A/C and alternator and power steering. The belts in the picture are wrong, it was to check and see if it looked right. I am wondering what is the best way to have the belts.Option # 1 one belt goes from the A/C to the crank to the water pump and back to the A/C. That is the line of groove...	Marten	9	668	Nov 17, 2020 by 123pugsy
	Battery mounting (Preview) If anyone is starting a project on a channeled model A Tudor and wondering where to store the battery, I looked all around under there and it seems to me that the only place to hide a full size battery is behind the passenger or driver seats under the floor. Especially if you plan to bag your ride and need a...	Cuddles	2	619	Nov 12, 2020 by Cuddles
	protecting vinyl and rubber (Preview) Hi started looking for something to help slow the cracking of dash pads and tires, etc. In my search came across this product called 303 Aerospace Protectant on Amazon but its not cheap and as always the reviews are mixed. Thought I'd ask and see what others are using. Paul	Rockhauler	2	681	Oct 27, 2020 by Rockhauler
	Music (Preview) Interested if anyone is playing music in their hot rod with an ipod, no radio. Thanks -- Edited by TIREDIRN on Saturday 24th of October 2020 02:04:58 PM	TIREDIRN	6	670	Oct 25, 2020 by TIREDIRN
«First < 1 2 3 4 … 16 > Last» \| Page of 16 sorted by