Tech

oldkoot · oldkoot

Just bought the car so starting from square one, the owner said everything was working fine before. The fan wouldn't start either by the temp sensor or the overide switch, jumpered the relay and the fan motor runs. Power at circuit breaker and terminal 87 at the relay, replaced the relay to be safe. Pu...

Rebelrod · Rebelrod

Hello I am looking at installing a Tachometer gauge in the location of the clock on my dash (49 ford club coupe) I am having trouble figuring out what size gauge I would need to fit in the 2 3/4" hole. Any ideas??? I cant seem to figure this out

hemikev · hemikev

Can any 1 local to me do ... ( hamilton ) ive never done anything like this before .. thanx Kev

scott420p · scott420p

I can pick up a Allstar 3000 converter for $200 are they even worth my time or should I save the money to buy a better one.

hemikev · hemikev

just picked up a set of headers for my t bucket project ... they are not chrome ...can you powder coat headers ????????????????

dualquadpete · 77

I seen electirc trailer brake , break away kits that use a motorcycle sized battery Question , do you think that size battery would be any good to run an electric winch ?? Probably not . I dont wanna fit two battery,s to the trailer . Or just use regular car size battery for winch an break away . Like do yo...

Malibu Man · Malibu Man

Well,it's time for a brake booster, master cylinder and proportioning valve for the malibu. Has anyone delt with John Stuart in Stoney Creek? I talked to them on the phone,and they have what I need,but want to be sure there okay.

scott420p · scott420p

I'm doing a rear brake line on my 1990 cherokee. I can't find the fitting that goes into the proportioning valve. Its a 3/16" tube nut with a 1/2-20 thread. I can find it online in the states. I tried cisco but they told me it'll be 4 weeks or more because they just got they're order in, and the manufact...

Iwannagofast · Iwannagofast

Hi folks, I came across this site yesterday and found it really helpful. Enter your make and model, wait for the page to load then click "Go to matching patterns" If you're looking for a wheel with different offset this really narrows the field in a hurry. http://www.roadkillcustoms....

Ragtop · Ragtop

Is it steel? And can it be welded OK? I was thinking about removing the bolts that hold it in place, tilting it out a bit to chop the top and then cut the excess off the top, but it's riveted to one side of the quarter panel and it's almost impossible to get the rivets out even though I've knocked the heads off o...

atomsplitter · atomsplitter

I'm going to be swapping out my transmission and I was looking for some reliable information on torque converters so I came straight to the internet! The motor is stock out of an 1995 Impala SS (260 hp/300 ft/lbs), 700r4, 3:42 rear and it weighs 3200lbs (without my fat ass in it). The truck is about 1000 l...

fatstax · fatstax

ok i have noticed on many rats and rods the front axle is leaned back, i assumed this had some purpose but i never put much thought into it. i was talking to a guy i know that has the yellow flamed t bucket at armdrop, we started discussing my rat truck and i asked him why the axle was leaned back, he told me tha...

Gearhead · Gearhead

Someone was asking about POR 15 a while ago - I picked up a supposedly equivalent product and thought I'd share my thoughts on what NOT to do. I picked up DOM16 which is made by a Canadian company @ half the cost. I applied it for the first time yesterday and was VERY DISAPPOINTED. I followed the instruct...

Gearhead · Gearhead

So I buy 3 cans of duplicolor engine ename to paint an engine and genset for my old lincoln welder that I'm rebuiliding. I just got through hours of removing DOM16 and was nearly ready to paint when I noticed in the "instructions" that bare metal needs to be primed. With engine enamel???? WTF...

howardp13 · howardp13

efi 5 liter 30 over built to be blown have some rocker problems hitting valve cover have 1 inch ford racing spacer goes between upper and lower intake so i can run taller covers what i need to know will it stand the test of time and how will it afect or will it afect rpm tork so what we have is a mass air motor w...

flatblack55delivery · flatblack55delivery

OK here is the problem .What kind do yuu guys use.I cannot belive the trouble I am having.Cheap ones metal ones glue stacks 3or 4 deep(I was desperate).Fatstax even welded me up new flanges on them,They are straight we checked and the gaskets are gone again.I have ordered a set of I think they are cal...

scott420p · scott420p

I'm building my first th350 and have a rebuild kit that i waited a while. But during teardown I relized I needed a intermediate roller clutch when it fell apart in my hands. Can I get theses new around the gta and from where? I can find them but only online and in the usa.

Iwannagofast · Iwannagofast

Okay guys, might as well start gathering info for a winter project ahead of time. We want to change both the Falcon and the Comet over to front disc / dual master & proportioning valve set-ups this winter. I've read so much stuff regarding this swap my head hurts. Monarch / Fairmont / Geo / ect, ect. W...

entourageguy · 77

Hey all , looking for a decent interior guy from Toronto , north to Barrie area . The tweed like part of the door panels on my wife,s 87 trans am have dried out an shrunken . 1/2 inch gap tween material and plastic part that its sposed to be bonded to . Want that replaced ..77.

ve3oky · ve3oky

Looking for recommendations on a good Machine shop, got a Buick 430 Block and heads that needs some lov'in. Im in Niagara Falls but willing to travel some to get it done right. Thanks

flatduck · flatduck

ok a car guy should know ........but i don t and if i don t ask i ll never know ........flat piston what does it do.......... increse hp or just better and more reliable ?

sebright · sebright

i have a pete & jakes model a frame and now i have bought a ford motor mount kit for my 5.0l can anyone give me a diagram or something on how to install the mounts

scott420p · scott420p

I have an 84 s10 with a sunroof that I just don't want its a PITA. I'm looking to have sheet metal welded in. Can anyone around the GTA do this or know a reputable shop to go to? I'm not worried about the paint as I'd be happy with primer.

flatblack55delivery · flatblack55delivery

Does anyone know if or how a 98 2.2 will fit in a 95 S10 with same size engine that has blown I know there are some differences between the engines We know there are sensors in the 98 that are not in the 95 but can they be by passed and still pass an Etest? do the intakes interchange if we want to use the 95 intake...

Torquewar · Torquewar

Hey guys there is a lengthly thread on emmisions on the board and its got me thinking time to pony up with some parts. Im looking to buy some high flow cats when i get my new headers and going over some sites im trying to determine the best ones to buy. There are probably several out there but has anyone bou...

61 poncho · 61 poncho

would the tail shaft in a pre 1986 700r4 with mechanical gears be the same as the later ones with the electronic speedo, thanks brent

howardp13 · howardp13

cab on s10 done. rear of truck is getting tubed. not 4 link not ladder bar useing parts out of my yard. we have 83/4 dodge with 391 that is 33.5 wide on super stock leafs. have 29x18.5x15 m/ts pro sport tires. would like to see some pics or prints to see the best way to do this all ready put in front cross member...

Beachcat · Beachcat

What would be the best gasket material / thickness to place between a glass body and its chassis?

Beachcat · Beachcat

I picked up a couple of 1932 Ontario license plates. I cleaned them up and painted them and now I'm looking for someone who can paint the numbers that are embossed on them. I'm in the Schomberg or Wasaga Beach area if anyone would do this. Thanks

Beachcat · Beachcat

This might seem like a stupid question for some but how do I pull an axle out of a 9" Ford rear end? Is it a simple procedure?

Beachcat · Beachcat

can anyone decode this casting number? Thanks 1M0519 3ZZ4

Beachcat · Beachcat

I would like to change some rear tires from a 26" OD tire to a 30" OD tire. I running a 350 tranny and a 9" ford rear end. Other than confusing the speedo, are there any reasons why this might not be a good idea. fenders are not an issue. Thanks

Beachcat · Beachcat

What are the recommended lift pad points on a 32Ford coupe? Thanks! -- Edited by Beachcat on Sunday 29th of July 2012 08:46:46 PM

Iwannagofast · Iwannagofast

Hy guys, I'm back with onother issue. We purchased a 63 Comet ragtop last year as a gift for my Dad who since has passed away. Previous owner had over heating problems and replaced the rad with a 4 row unit. Our Falcon had similar issues when first built. It has a '69 302 Windsor / C4. We installed a 190' ther...

flatblack55delivery · flatblack55delivery

The plan, 93 Roadmaster 350(Chevy)change the cam and intake to carb.The cam I have little information on except it worked well with the intake in my last high milage engine till the crank berrings went.The question we changed the roller lifters to reg chevy style,(hydrolic?)because it was suggest...

39poncho · 39poncho

I have a 68 Turbo 400 with a long snout in my 67 Cutlass. It actually fits well vut when I went to hook up the speedo cable I realized there is no provision for one. apparently some of the big Olds back then drove the speedo from the front wheel. So the big Question is what do I do now to solve this problem? Will t...

will · will

Can anyone recommend a media blasting shop that they know or have had work done by them and were satisfied with the results? There seems to be so many types of "media material" also. What is the best? I am looking to have the complete exterior blasted down to bare metal and then primed for...

jadranjohn · jadranjohn

Hi, I have a crank from a early hemi (392) and I am looking for a shop to grind the crank. Do any of you know of a shop I should send it to in Eastern Ontario. This is a rare crankshaft and I would like to send it to someone who won't f$$k it up. Thanks, John

Gearhead · Gearhead

Hey, does anyone have dimensions for a heavy duty shop crane? I have a 3ton long arm jack and want to build a knock down shop crane instead of buying one of those fold up deals. My shop space is pretty tiny, I want to make one that comes apart into separate components and stand them up in the corner or oil drum...

flatduck · flatduck

hi trying to put the top back up and short of a little bit ........door gap looks ok .is there any ajustment that can be made ? never own a ragtop before is this a current thing with ragtop ? help help

rat39 · rat39

Does anyone know of a place that has experience redrilling axle flange?I have a ford 9 with 5 on 4.5 and I waant to add 5 on 4.75.thxbob.

Rookie rodder · Rookie rodder

i have a question regarding the oil pressure reading on my 53 chevy 235. i just finished rewiring the car for 12 volt from 6 plus new automterer gauges etc. i took the car out for a spin to test her out. the car ran great but my oil pressure gauge was not reading. had my dads mechanic take a look at it. thought ...

Youngoldguy · Youngoldguy

I have an EZ Wirirng harness. With my health now it is hard to get under the car and REALLY hard to get under the dash. Anybody in Fergus/Guelph area that can help me in exchange for my help on their project or for a reasonable fee? I can certainly help pull it, actually going to try start it this week. Thanks...

flatblack55delivery · flatblack55delivery

My son is customizing a 96 Roadmaster wagon and has removed the woodgrain and trim .We are left with a couple of holes and a whole bunch of small nail like studs that held on the trim.The holes we know what to do with,the question is what do we do with the studs.They seam secure and the couple that we broke o...

30AV8 · 30AV8

I've got a 74 C4 tranny in my pickup and the problem I am having is repeatable. When driven for the first 5 minutes, it does not want to shift out of low. After 5 minutes it shifts fine. I've checked the fluid several times when in park and after driven awhile, it shows full, doesn't smell, and is nice'n p...

henrys57wagon · henrys57wagon

The gas gauge on the wagon quit a while ago so I picked up a Ford brass float and changed it to night. The old float has gas in it. The gauge moved to about 1/4 so lets hope when I fill it up it will be accurate. Many GM/ Chrysler and Fords use the same float. COAZ-9202-B.

poncho62 · poncho62

I know this sounds like a newb question, but I have been using 10w30 oil in my vehicles for all my life (5w30 in the modern daily driver)......My oil pressure is decent in my truck, but the engine has 18 years and quite a few miles on it now....What will 10w40 do for me, if anything?

Brianandhisbad55 · Brianandhisbad55

Can I get some advice as to what product people are using to clean and polish billet aluminum? I have billet valve covers on my '55 and want to keep them looking good. Thanks!

48poncho · 48poncho

dont know much about torque converters other than i need one and not sure what i need i have a 454 BB about 540 hp mated to a turbo 400 tranny any help would be great cheers Brian

Chris58 · Chris58

Last year I had a run of wheel bearing and brake issues on my 58. I remedied the front wheel bearing issue by upgrading to a taper bearing hub kit. Done. The brakes were a whole new bag of tricks. I kept this car stock with 4-wheel non-power drums and the single suicide master cylinder. I ended up replacing...

Topic		Started By	Replies	Views	Last Post
	Cooling fan not working (Preview) Just bought the car so starting from square one, the owner said everything was working fine before. The fan wouldn't start either by the temp sensor or the overide switch, jumpered the relay and the fan motor runs. Power at circuit breaker and terminal 87 at the relay, replaced the relay to be safe. Pu...	oldkoot	9	1403	Nov 11, 2012 by oldkoot
	Gauge size (Preview) Hello I am looking at installing a Tachometer gauge in the location of the clock on my dash (49 ford club coupe) I am having trouble figuring out what size gauge I would need to fit in the 2 3/4" hole. Any ideas??? I cant seem to figure this out	Rebelrod	16	1673	Nov 9, 2012 by 427CARL
	reversing corvair box , any 1 local can do ( hamilton ) (Preview) Can any 1 local to me do ... ( hamilton ) ive never done anything like this before .. thanx Kev	hemikev	4	2943	Nov 5, 2012 by fatstax
	Thoughts On Allstar Performance Converters (Preview) I can pick up a Allstar 3000 converter for $200 are they even worth my time or should I save the money to buy a better one.	scott420p	14	1394	Nov 4, 2012 by scott420p
	powder coating (Preview) just picked up a set of headers for my t bucket project ... they are not chrome ...can you powder coat headers ????????????????	hemikev	8	1722	Oct 29, 2012 by Sacotu
	Elektric trailer brakes (Preview) I seen electirc trailer brake , break away kits that use a motorcycle sized battery Question , do you think that size battery would be any good to run an electric winch ?? Probably not . I dont wanna fit two battery,s to the trailer . Or just use regular car size battery for winch an break away . Like do yo...	77	25	4043	Oct 25, 2012 by dualquadpete
	Brake booster. (Preview) Well,it's time for a brake booster, master cylinder and proportioning valve for the malibu. Has anyone delt with John Stuart in Stoney Creek? I talked to them on the phone,and they have what I need,but want to be sure there okay.	Malibu Man	2	898	Oct 23, 2012 by Malibu Man
	Brake Line Fittings (Preview) I'm doing a rear brake line on my 1990 cherokee. I can't find the fitting that goes into the proportioning valve. Its a 3/16" tube nut with a 1/2-20 thread. I can find it online in the states. I tried cisco but they told me it'll be 4 weeks or more because they just got they're order in, and the manufact...	scott420p	18	2571	Oct 22, 2012 by dualquadpete
	Wheel bolt pattern cross reference site (Preview) Hi folks, I came across this site yesterday and found it really helpful. Enter your make and model, wait for the page to load then click "Go to matching patterns" If you're looking for a wheel with different offset this really narrows the field in a hurry. http://www.roadkillcustoms....	Iwannagofast	5	3095	Oct 21, 2012 by Iwannagofast
	Ya know that T shaped strip on Model T and A's? (Preview) Is it steel? And can it be welded OK? I was thinking about removing the bolts that hold it in place, tilting it out a bit to chop the top and then cut the excess off the top, but it's riveted to one side of the quarter panel and it's almost impossible to get the rivets out even though I've knocked the heads off o...	Ragtop	4	1236	Oct 19, 2012 by Chris Stapley
	?'s About Torque Converters (Preview) I'm going to be swapping out my transmission and I was looking for some reliable information on torque converters so I came straight to the internet! The motor is stock out of an 1995 Impala SS (260 hp/300 ft/lbs), 700r4, 3:42 rear and it weighs 3200lbs (without my fat ass in it). The truck is about 1000 l...	atomsplitter	3	1075	Oct 11, 2012 by atomsplitter
	eight degrees (Preview) ok i have noticed on many rats and rods the front axle is leaned back, i assumed this had some purpose but i never put much thought into it. i was talking to a guy i know that has the yellow flamed t bucket at armdrop, we started discussing my rat truck and i asked him why the axle was leaned back, he told me tha...	fatstax	18	1793	Oct 7, 2012 by SKAR
	POR15 vs DOM16 (Preview) Someone was asking about POR 15 a while ago - I picked up a supposedly equivalent product and thought I'd share my thoughts on what NOT to do. I picked up DOM16 which is made by a Canadian company @ half the cost. I applied it for the first time yesterday and was VERY DISAPPOINTED. I followed the instruct...	Gearhead	14	24273	Oct 5, 2012 by will
	CT & Part Source rant (Preview) So I buy 3 cans of duplicolor engine ename to paint an engine and genset for my old lincoln welder that I'm rebuiliding. I just got through hours of removing DOM16 and was nearly ready to paint when I noticed in the "instructions" that bare metal needs to be primed. With engine enamel???? WTF...	Gearhead	5	1691	Sep 30, 2012 by Gearhead
	supercharge 52 f1 (Preview) efi 5 liter 30 over built to be blown have some rocker problems hitting valve cover have 1 inch ford racing spacer goes between upper and lower intake so i can run taller covers what i need to know will it stand the test of time and how will it afect or will it afect rpm tork so what we have is a mass air motor w...	howardp13	4	1485	Sep 22, 2012 by hemi43
	header gaskets (Preview) OK here is the problem .What kind do yuu guys use.I cannot belive the trouble I am having.Cheap ones metal ones glue stacks 3or 4 deep(I was desperate).Fatstax even welded me up new flanges on them,They are straight we checked and the gaskets are gone again.I have ordered a set of I think they are cal...	flatblack55delivery	17	1855	Sep 21, 2012 by RacerRick
	TH350 rebuild (Preview) I'm building my first th350 and have a rebuild kit that i waited a while. But during teardown I relized I needed a intermediate roller clutch when it fell apart in my hands. Can I get theses new around the gta and from where? I can find them but only online and in the usa.	scott420p	9	1216	Sep 19, 2012 by hemi43
	Disc brakes / Master cylinder (Preview) Okay guys, might as well start gathering info for a winter project ahead of time. We want to change both the Falcon and the Comet over to front disc / dual master & proportioning valve set-ups this winter. I've read so much stuff regarding this swap my head hurts. Monarch / Fairmont / Geo / ect, ect. W...	Iwannagofast	13	1736	Sep 18, 2012 by Iwannagofast
	Decent Interior guy (Preview) Hey all , looking for a decent interior guy from Toronto , north to Barrie area . The tweed like part of the door panels on my wife,s 87 trans am have dried out an shrunken . 1/2 inch gap tween material and plastic part that its sposed to be bonded to . Want that replaced ..77.	77	5	1630	Sep 17, 2012 by entourageguy
	Machine Shop (Preview) Looking for recommendations on a good Machine shop, got a Buick 430 Block and heads that needs some lov'in. Im in Niagara Falls but willing to travel some to get it done right. Thanks	ve3oky	4	1122	Sep 11, 2012 by ve3oky
	an easy answer for some (Preview) ok a car guy should know ........but i don t and if i don t ask i ll never know ........flat piston what does it do.......... increse hp or just better and more reliable ?	flatduck	12	1648	Sep 9, 2012 by 123pugsy
	motor mount help (Preview) i have a pete & jakes model a frame and now i have bought a ford motor mount kit for my 5.0l can anyone give me a diagram or something on how to install the mounts	sebright	0	1195	Sep 8, 2012 by sebright
	Sheet Metal Work (Preview) I have an 84 s10 with a sunroof that I just don't want its a PITA. I'm looking to have sheet metal welded in. Can anyone around the GTA do this or know a reputable shop to go to? I'm not worried about the paint as I'd be happy with primer.	scott420p	20	1892	Sep 8, 2012 by scott420p
	S10 Engine Swap (Preview) Does anyone know if or how a 98 2.2 will fit in a 95 S10 with same size engine that has blown I know there are some differences between the engines We know there are sensors in the 98 that are not in the 95 but can they be by passed and still pass an Etest? do the intakes interchange if we want to use the 95 intake...	flatblack55delivery	9	1295	Sep 5, 2012 by The Boy
	Exhaust (Cats) (Preview) Hey guys there is a lengthly thread on emmisions on the board and its got me thinking time to pony up with some parts. Im looking to buy some high flow cats when i get my new headers and going over some sites im trying to determine the best ones to buy. There are probably several out there but has anyone bou...	Torquewar	16	1833	Sep 3, 2012 by 77
	transmission help (Preview) would the tail shaft in a pre 1986 700r4 with mechanical gears be the same as the later ones with the electronic speedo, thanks brent	61 poncho	4	1061	Sep 2, 2012 by dualquadpete
	s/c 52 f1 (Preview) cab on s10 done. rear of truck is getting tubed. not 4 link not ladder bar useing parts out of my yard. we have 83/4 dodge with 391 that is 33.5 wide on super stock leafs. have 29x18.5x15 m/ts pro sport tires. would like to see some pics or prints to see the best way to do this all ready put in front cross member...	howardp13	5	1126	Aug 31, 2012 by hemi43
	gasket material (Preview) What would be the best gasket material / thickness to place between a glass body and its chassis?	Beachcat	7	1564	Aug 26, 2012 by Iwannagofast
	Looking to paint (Preview) I picked up a couple of 1932 Ontario license plates. I cleaned them up and painted them and now I'm looking for someone who can paint the numbers that are embossed on them. I'm in the Schomberg or Wasaga Beach area if anyone would do this. Thanks	Beachcat	14	3755	Aug 24, 2012 by Chris Stapley
	rear axle pull (Preview) This might seem like a stupid question for some but how do I pull an axle out of a 9" Ford rear end? Is it a simple procedure?	Beachcat	9	1436	Aug 18, 2012 by Beachcat
	decode an engine number (Preview) can anyone decode this casting number? Thanks 1M0519 3ZZ4	Beachcat	1	1265	Aug 8, 2012 by DaveM
	tire/wheel question (Preview) I would like to change some rear tires from a 26" OD tire to a 30" OD tire. I running a 350 tranny and a 9" ford rear end. Other than confusing the speedo, are there any reasons why this might not be a good idea. fenders are not an issue. Thanks	Beachcat	6	1227	Aug 2, 2012 by Beachcat
	jacking points (Preview) What are the recommended lift pad points on a 32Ford coupe? Thanks! -- Edited by Beachcat on Sunday 29th of July 2012 08:46:46 PM	Beachcat	18	1375	Jul 31, 2012 by Beachcat
	Overheating Comet (Preview) Hy guys, I'm back with onother issue. We purchased a 63 Comet ragtop last year as a gift for my Dad who since has passed away. Previous owner had over heating problems and replaced the rad with a 4 row unit. Our Falcon had similar issues when first built. It has a '69 302 Windsor / C4. We installed a 190' ther...	Iwannagofast	23	2434	Jul 31, 2012 by rat39
	Roller rockers and cam shafts (Preview) The plan, 93 Roadmaster 350(Chevy)change the cam and intake to carb.The cam I have little information on except it worked well with the intake in my last high milage engine till the crank berrings went.The question we changed the roller lifters to reg chevy style,(hydrolic?)because it was suggest...	flatblack55delivery	11	2093	Jul 30, 2012 by DaveM
	Turbo 400 with no speedo drive provision. (Preview) I have a 68 Turbo 400 with a long snout in my 67 Cutlass. It actually fits well vut when I went to hook up the speedo cable I realized there is no provision for one. apparently some of the big Olds back then drove the speedo from the front wheel. So the big Question is what do I do now to solve this problem? Will t...	39poncho	3	1286	Jul 26, 2012 by 39poncho
	Media Blasting - ? (Preview) Can anyone recommend a media blasting shop that they know or have had work done by them and were satisfied with the results? There seems to be so many types of "media material" also. What is the best? I am looking to have the complete exterior blasted down to bare metal and then primed for...	will	8	2212	Jul 26, 2012 by fatstax
	Crankshaft grinder in Eastern Ontario (Preview) Hi, I have a crank from a early hemi (392) and I am looking for a shop to grind the crank. Do any of you know of a shop I should send it to in Eastern Ontario. This is a rare crankshaft and I would like to send it to someone who won't f$$k it up. Thanks, John	jadranjohn	8	4067	Jul 24, 2012 by RacerRick
	Shop crane dimensions? (Preview) Hey, does anyone have dimensions for a heavy duty shop crane? I have a 3ton long arm jack and want to build a knock down shop crane instead of buying one of those fold up deals. My shop space is pretty tiny, I want to make one that comes apart into separate components and stand them up in the corner or oil drum...	Gearhead	1	1080	Jul 24, 2012 by will
	rag top problem (Preview) hi trying to put the top back up and short of a little bit ........door gap looks ok .is there any ajustment that can be made ? never own a ragtop before is this a current thing with ragtop ? help help	flatduck	11	1610	Jul 18, 2012 by flatduck
	redrilling axle flange (Preview) Does anyone know of a place that has experience redrilling axle flange?I have a ford 9 with 5 on 4.5 and I waant to add 5 on 4.75.thxbob.	rat39	13	6333	Jul 18, 2012 by fatstax
	no oil pressure reading (Preview) i have a question regarding the oil pressure reading on my 53 chevy 235. i just finished rewiring the car for 12 volt from 6 plus new automterer gauges etc. i took the car out for a spin to test her out. the car ran great but my oil pressure gauge was not reading. had my dads mechanic take a look at it. thought ...	Rookie rodder	1	1431	Jul 17, 2012 by Rusty Nuts
	I need help with wiring my rod (Preview) I have an EZ Wirirng harness. With my health now it is hard to get under the car and REALLY hard to get under the dash. Anybody in Fergus/Guelph area that can help me in exchange for my help on their project or for a reasonable fee? I can certainly help pull it, actually going to try start it this week. Thanks...	Youngoldguy	2	1127	Jul 15, 2012 by Youngoldguy
	A question for the bodymen (Preview) My son is customizing a 96 Roadmaster wagon and has removed the woodgrain and trim .We are left with a couple of holes and a whole bunch of small nail like studs that held on the trim.The holes we know what to do with,the question is what do we do with the studs.They seam secure and the couple that we broke o...	flatblack55delivery	2	1359	Jul 15, 2012 by slab
	C4 Trannny shifting issue (Preview) I've got a 74 C4 tranny in my pickup and the problem I am having is repeatable. When driven for the first 5 minutes, it does not want to shift out of low. After 5 minutes it shifts fine. I've checked the fluid several times when in park and after driven awhile, it shows full, doesn't smell, and is nice'n p...	30AV8	4	1406	Jul 5, 2012 by 30AV8
	fuel gauge float (Preview) The gas gauge on the wagon quit a while ago so I picked up a Ford brass float and changed it to night. The old float has gas in it. The gauge moved to about 1/4 so lets hope when I fill it up it will be accurate. Many GM/ Chrysler and Fords use the same float. COAZ-9202-B.	henrys57wagon	4	1343	Jul 4, 2012 by henrys57wagon
	10w40 oil? (Preview) I know this sounds like a newb question, but I have been using 10w30 oil in my vehicles for all my life (5w30 in the modern daily driver)......My oil pressure is decent in my truck, but the engine has 18 years and quite a few miles on it now....What will 10w40 do for me, if anything?	poncho62	9	2062	Jun 28, 2012 by fatstax
	Cleaning billet aluminum (Preview) Can I get some advice as to what product people are using to clean and polish billet aluminum? I have billet valve covers on my '55 and want to keep them looking good. Thanks!	Brianandhisbad55	15	30446	Jun 27, 2012 by Gazoo
	torque converter question (Preview) dont know much about torque converters other than i need one and not sure what i need i have a 454 BB about 540 hp mated to a turbo 400 tranny any help would be great cheers Brian	48poncho	4	2030	Jun 25, 2012 by SD66
	Who arcs brake shoes? (Preview) Last year I had a run of wheel bearing and brake issues on my 58. I remedied the front wheel bearing issue by upgrading to a taper bearing hub kit. Done. The brakes were a whole new bag of tricks. I kept this car stock with 4-wheel non-power drums and the single suicide master cylinder. I ended up replacing...	Chris58	24	2205	Jun 21, 2012 by Chris58
«First < 1 … 14 15 16 17 > Last» \| Page of 17 sorted by