Tech

shag766 · shag766

it is a stock 70 chevelle h/t car with some big power that i am asking about. i don't notice much stress with street tires on but with the slicks it is noticeable and i am not sure where or how to add some support to the frame. gusset the corners is probably a starter point but is there some other places to thi...

damion · damion

I installed a new set of leaf springs in my '67 Camaro. I'd liked the stance as it was but the leaf bundles had separated so I measured it up and found it was 1" lower than stock and ordered a new set with a 1" drop. The problem is that the car is a convertible and the extra weight must have them compressed mor...

wuga · wuga

Somewhere along the way, I lost the retaining plate that holds the speedometer cable drive into the side of the transmission. This is a super t10 and I don't remember which style it is. I have seen a flat bar with a bolt hole in the end and also have seen as on my T5, a horseshoe shape with a bolt hole at the t...

South Shore · South Shore

Went all over looking for "IAT" (Inorganic Additive Technoligy) type antifreeze for an old cast iron block with a copper and brass radiator.I am looking for a Brand name product. Every auto store or jobber place I went to was "buffamoomed" when I asked for it specifically.Their "idea" of an old car n...

two tone 56 · two tone 56

My YOM plates are in need of a repaint,does anyone know who does this service in Ontario ?

hotrodford8 · hotrodford8

Hi can we install 350 timing cover on roller vortech block / carbelt is useless refuse to talk / comp will not answer phone / help please am told we can use old school cover with a little mod / also will 300 duration hi lift cam work on marine boat motor , 1.5 drive 64 cc chamber , flat top piston , 200 or 220 int...

billyisamountain · billyisamountain

The main bearings on my Gen1 5.7L SBC are stamped with .0006. What does that mean? JG

stang · stang

Frame is coming along nicely on the Merc, time to start looking for an air ride/ lowering system. anyone know of a dealer close to London that can help, Thanks Ron.

Undead_Edsel_59 · Undead_Edsel_59

I got my 66 olds dynamic on the road, after a bit of driving my signal switch broke, if I can get the part that pivots off, I think I can fix it. Does anyone know if that comes off the switch assembly? As Its old and brittle and don't want to break it more than it is. I think there is a tab, that pushes the copper...

Undead_Edsel_59 · Undead_Edsel_59

I've open'd the glove box a million times on my 66 Olds. Now that my insurence and ownership are in there it refuses to open for anything. I've been at it for an hour now, seems it has to be open to take any of it apart. It's not locked. The latch is obviously broke. I've tried using a small pick, and other thin...

wuga · wuga

Here is a little exercise I would like you to do. If you know how much torque your engine puts out and if you know your first gear ratio and you know your rear end ratio, multiplying these three numbers together should give your torque at the rear wheel. i.e. 260 (torque expected from 261) x 2.52 (1st gea...

studeshaker · studeshaker

i have a part number for a rebuilt delco distributor 366/427 tall deck. however, it also lists it as fitting a 350 medium duty truck. anyone know anything about this 350 and why it would take a tall deck distributor ? is the manifold on this 350 taller by .400" or something ? i'd like to order one for m...

Roboticist · Roboticist

Good morning! My '52 body seems to have a VIN stamped on the firewall. It's really hard to see. The main VIN plate is missing and I have no ownership. There is no frame. So here's the question. What is the best method to read this VIN? I have heard a lot of stories of what guys have tried, and I don't want...

72endurawagon · 72endurawagon

Anybody use London drive systems off of highbury south for driveshaft work? I have one that needs to be shortened and balanced,any info welcome!

wuga · wuga

I am building a nostalgia altered. It is expected to weigh in at about 16-1700 pounds. I am using a 261 Pontiac 6 cylinder rated at about 275 hp and about 260 ft. lb. of torque. I am running 9" by 29" slicks. I was going to run an aluminum Powerglide, but I don't think 1st gear is low enough. ...

hotrod-steve · hotrod-steve

Will the newer style vortec heads work on an older ( 1986 ) 350 ?

Hibred · Hibred

Guys I have a 62 Chevy 11 Nova, the trim pieces I am talking about go on the doors right beside the window where your arm would rest if you had it out the window and on the small window in the passenger area same place, The pieces I have now are in nice shape and have polished up perfectly but the problem I have...

South Shore · South Shore

Do you use the same hydrometer to check green antifreeze as pink antifreeze?

taz 76regal · taz 76regal

Hi all have a trailer brake controller installed previously in my 76 regal,how can I removed it.

cheyenne · cheyenne

Has anyone had any experience with installing a ( Pusher ) Flex-A-Lite electric fan on their radiator, ?? They come with a set of 4 plastic bolts, and fast nuts. I have a problem with the idea of feeding a small philips screw driver through the core of a brand new aluminum radiator, ( as the installat...

South Shore · South Shore

What upgrades should be considered when getting a mid 70's 350 TH transmission rebuilt for street use?

Rustynuts · Rustynuts

I have a snap-on m2500 but it won't work on the 07 chevy and I don't want to spend a lot of money for the cables and cartridge. I have a code reader but am looking for a decent scanner that will give me live data that shows tps etc. and not cost me a lot of $$$$. Any suggestions?

willys392 · willys392

Gidday folks, I have a small bearing 9" rear diff from a 67 Fairlane with 10"x 2.5" brakes. I got the rear end w/o the drums. I'm looking for drums to fit and I can get the proper ones but the money they want for them is outrageous ( Carquest $173 per). Are there any late model drums they w...

Randyr · Randyr

Hi folks, I bought the Edelbrock 4 bbl EGR plate for the 302 and have found that the gasket that goes under it has an opening that is a bit too long on the supply side to the EGR valve and extends to the downstream side by about 1/8 of an inch, creating a situation where exhaust gas can bypass the EGR valve enti...

Whitey · Whitey

http://www.kijiji.ca/v-classic-cars/city-of-toronto/72-swinger-looking-for-...

dualquadpete · dualquadpete

Just had a call from a guy about his 34 Plymouth he just got, he's trying to find out what the PE model stands for??? I remember when I worked for Chrysler back in the late 60's that they had a P series some ended in a F ?? Anybody know the answer?? Thks Pete

wbeaton · wbeaton

I am considering options for an upcoming engine swap. I want to add dual exhaust to a 235 Chevy I6. I like the look of a split manifold, but I'm concerned it won't flow well enough. I also don't have the ability to weld cast iron so I'd have to find a shop to do it. Of course, I could bolt on Fenton headers and be...

stang · stang

After months of research and measurements I think I have found a donor car. 1976 Ford Cougar, Florida car. wheelbase is very close side to side. saved everything, power windows, brake booster heater core & fan etc. will post some pics once I get the body off. -- Edited by stang on Monday 28th of Marc...

V2addict · V2addict

Has anyone ever made their own sound deadener?? I've done a little web search and apparently this stuff is easy to make, just thought I would ask if anyone here has tried and if it worked out as expected or advertised? Angelo

fleet 51 · fleet 51

I 've seen these meters shown in magazines -- Is it just a matter of installing an O2 sensor in header and connecting it to the guage ?? Somehow it all sounds too simple -- But , I have zero knowledge of these things -- Would enjoy some pointers --- THANKS in Advance -- DON / Fleet 51

Seeker1056 · Seeker1056

does anyone know of any companies still in business who still make custom offset wheels?

cheyenne · cheyenne

Anyone have any experience adding some lift to a '54 ford front end ?? Nothing too radical,..( approx. 2" ),..don't want it looking like a " Gasser ". I can jack the ass end up by using Gabriel ( Rear ) air shocks manufactured for the car,..can't seem to find any for the front, and I don'...

sherlock · sherlock

I am on my 3rd. buick supercharged motor (all different years) they all have motor knock under load, gas milage is good, no oil burning. put 60,000 klix on last one.anybody else have similar problem?

Seeker1056 · Seeker1056

anyone out there know how to take the hardness out of a bolt I have several control arm bolts seized into the sleeve/bushings and will have to use a sawzall to cut them out - problem is they are Grade 8 hardness and eat sawzall blades like no tomorrow is there something I can do on the car to remove some or al...

tc · tc

Looking for a 57 Chev 2dr. builder. No motor and transmission ok. Not looking for perfect but don't want junk.

Rustynuts · Rustynuts

my 90 chevy pu needs more pressure since it only sprays at the bottom ....I have new adjustable nozzles and are pointed as high as they will go. probably pump is worn being 25 yrs old but would rather use a pump unit from a newer vehicle. Any ideas ?

hotrod-steve · hotrod-steve

I have an after market parallel leaf kit in my 39 Ford coupe and the springs ride flat which results in a rather stiff ride. I like the ride height so I don't want to re arc the springs so my plan is to remove a couple of leaves and install air bags to retain the ride height ,hoping this will smooth the ride. Ha...

Marten · Marten

So I go to put my cab on the frame today as I had some extra people around to help. As you can see in the pictures the cab hits the dist. before the mount holes line up. I still need to move the cab forward about 2-2 1/2". Currently the motor mounts are welded in line and on top of the front cross member....

supernash · supernash

I was at a buddies shop a couple years ago. He runs Quick32 @ 7 seconds or some such. Anyway, we were having a beverage or 10 putting the car back together for it's morning load and go. First time I even saw his new car btw. When we're all done, except a door, he says grab that door hanging on the wall. Ya full do...

V2addict · V2addict

Can anyone tell me if there is a way to refurbish original glass, I have the original front windshield out of my 1956 F-100 and it has a line where the windshield wipers were, it is as if the blade was worn out and the wiper arm was allowed to sit on the window. Thank you, Angelo

wuga · wuga

I have a 2014 F250 diesel crew cab short box. I am towing a large 5th wheel with a hitch weight of about 2000 lbs. When I hook up, my bumper drops about 4". I would like to install a set of load leveling shocks to prevent the drop and as well stop the up and down oscillation on bumpy roads. Does anyone...

South Shore · South Shore

Does anyone know of a shop that has a trany dyno that can check the operation of an automatic transmission?

LT · LT

Iam learning how to weld from this awesome new school. The rates are cheap and in a few months your a certified welder. You can what ever you want have your own business or get a job right away. just thought id say something because I find its an awesome help now when Iam fabricating or welding something on...

wuga · wuga

I've seen this happen on so many late model cars. The rear rotors rust up because the sliders seize. The pads are like new but they say the rotors must be replaced. How do you get around repairing the surface of the rotors so the rear brakes function, which they never do and that is why the problem in the...

Rustynuts · Rustynuts

my 90 chevy has been noisy lately so today I see that there is a small about 1-1/4" dia plug that is on the bottom of the cat that is loose rusted and rattling. Why is there such a plug on a catalytic converter?

apachomatic · apachomatic

Hi guys, I am trying to decide which way to go with the rear suspension of my '59 Apache. I want to keep the leafs but I am wondering if anyone has used air shocks. I am looking at the Monroe Max-Air shocks. The description indicates that they are more meant for leveling a load for towing or heavy loads...

flatblack55delivery · flatblack55delivery

Well the rearend seized up on my sons s10 pickup. I hve been reading that the way to go on this is to pickup a Ford Explorer rear and the bonis is it bolts up and has disks as well . There is talk about the offset pumpkin causing issues and others say no problem. I understand the bolt pattern is different and it...

hotrod-steve · hotrod-steve

I have a 454 and want to use a 700R4. What flex plate do I use? The motor is stock and the trans has been beefed up.

South Shore · South Shore

I put a question on the tech forum about antifreeze. Got some good replies, thank you. I was unable to access more than half of them. Still getting email notification on people replying but when I click on them to see them they are not on the forum page. People tried to help me access them with numerous su...

Seeker1056 · Seeker1056

Anyone out there know of a reasonable supplier here in Ontario for hot rod wiring harnesses? 12 circuit or more also looking for someone who does the LS motor harness rewire service new project is going to be modern efi and automatic OD if it kills me lol

Topic		Started By	Replies	Views	Last Post
	frame support ideas sought (Preview) it is a stock 70 chevelle h/t car with some big power that i am asking about. i don't notice much stress with street tires on but with the slicks it is noticeable and i am not sure where or how to add some support to the frame. gusset the corners is probably a starter point but is there some other places to thi...	shag766	13	1442	Apr 20, 2016 by RacerRick
	Raising Rear Suspension leaf spring suspension raise (Preview) I installed a new set of leaf springs in my '67 Camaro. I'd liked the stance as it was but the leaf bundles had separated so I measured it up and found it was 1" lower than stock and ordered a new set with a 1" drop. The problem is that the car is a convertible and the extra weight must have them compressed mor...	damion	7	1387	Apr 18, 2016 by damion
	speedometer cable retainer (Preview) Somewhere along the way, I lost the retaining plate that holds the speedometer cable drive into the side of the transmission. This is a super t10 and I don't remember which style it is. I have seen a flat bar with a bolt hole in the end and also have seen as on my T5, a horseshoe shape with a bolt hole at the t...	wuga	0	1131	Apr 16, 2016 by wuga
	"IAT"(Inorganic Additive Technoligy) Antifreeze (Preview) Went all over looking for "IAT" (Inorganic Additive Technoligy) type antifreeze for an old cast iron block with a copper and brass radiator.I am looking for a Brand name product. Every auto store or jobber place I went to was "buffamoomed" when I asked for it specifically.Their "idea" of an old car n...	South Shore	3	1437	Apr 13, 2016 by Petebil
	License Plate Restoration (Preview) My YOM plates are in need of a repaint,does anyone know who does this service in Ontario ?	two tone 56	35	23011	Apr 9, 2016 by Ground Pounder
	5.7 350 chev gm help (Preview) Hi can we install 350 timing cover on roller vortech block / carbelt is useless refuse to talk / comp will not answer phone / help please am told we can use old school cover with a little mod / also will 300 duration hi lift cam work on marine boat motor , 1.5 drive 64 cc chamber , flat top piston , 200 or 220 int...	hotrodford8	5	1451	Apr 6, 2016 by RacerRick
	main bearing question (Preview) The main bearings on my Gen1 5.7L SBC are stamped with .0006. What does that mean? JG	billyisamountain	4	1092	Mar 31, 2016 by Petebil
	Air Bags (Preview) Frame is coming along nicely on the Merc, time to start looking for an air ride/ lowering system. anyone know of a dealer close to London that can help, Thanks Ron.	stang	3	1139	Mar 28, 2016 by toomuchjunk
	66 olds signal switch (Preview) I got my 66 olds dynamic on the road, after a bit of driving my signal switch broke, if I can get the part that pivots off, I think I can fix it. Does anyone know if that comes off the switch assembly? As Its old and brittle and don't want to break it more than it is. I think there is a tab, that pushes the copper...	Undead_Edsel_59	5	1422	Mar 27, 2016 by Undead_Edsel_59
	Glove box won't open. Any ideas? (Preview) I've open'd the glove box a million times on my 66 Olds. Now that my insurence and ownership are in there it refuses to open for anything. I've been at it for an hour now, seems it has to be open to take any of it apart. It's not locked. The latch is obviously broke. I've tried using a small pick, and other thin...	Undead_Edsel_59	8	1561	Mar 25, 2016 by Petebil
	torque application (Preview) Here is a little exercise I would like you to do. If you know how much torque your engine puts out and if you know your first gear ratio and you know your rear end ratio, multiplying these three numbers together should give your torque at the rear wheel. i.e. 260 (torque expected from 261) x 2.52 (1st gea...	wuga	8	1359	Mar 25, 2016 by shag766
	tall deck distributor. (Preview) i have a part number for a rebuilt delco distributor 366/427 tall deck. however, it also lists it as fitting a 350 medium duty truck. anyone know anything about this 350 and why it would take a tall deck distributor ? is the manifold on this 350 taller by .400" or something ? i'd like to order one for m...	studeshaker	3	1262	Mar 17, 2016 by RacerRick
	VIN code reading? (Preview) Good morning! My '52 body seems to have a VIN stamped on the firewall. It's really hard to see. The main VIN plate is missing and I have no ownership. There is no frame. So here's the question. What is the best method to read this VIN? I have heard a lot of stories of what guys have tried, and I don't want...	Roboticist	12	1806	Mar 13, 2016 by chips
	London Drive Systems? (Preview) Anybody use London drive systems off of highbury south for driveshaft work? I have one that needs to be shortened and balanced,any info welcome!	72endurawagon	6	1875	Mar 11, 2016 by 72endurawagon
	What GM transmission to use (Preview) I am building a nostalgia altered. It is expected to weigh in at about 16-1700 pounds. I am using a 261 Pontiac 6 cylinder rated at about 275 hp and about 260 ft. lb. of torque. I am running 9" by 29" slicks. I was going to run an aluminum Powerglide, but I don't think 1st gear is low enough. ...	wuga	6	1584	Mar 10, 2016 by RacerRick
	Chevy Vortec heads (Preview) Will the newer style vortec heads work on an older ( 1986 ) 350 ?	hotrod-steve	2	1278	Mar 10, 2016 by RacerRick
	Need advice regarding trim pieces on 62 Nova (Preview) Guys I have a 62 Chevy 11 Nova, the trim pieces I am talking about go on the doors right beside the window where your arm would rest if you had it out the window and on the small window in the passenger area same place, The pieces I have now are in nice shape and have polished up perfectly but the problem I have...	Hibred	7	1533	Mar 10, 2016 by shawn63
	Antifreeze Question (Preview) Do you use the same hydrometer to check green antifreeze as pink antifreeze?	South Shore	3	1675	Mar 9, 2016 by supernash
	trailer brake controller (Preview) Hi all have a trailer brake controller installed previously in my 76 regal,how can I removed it.	taz 76regal	4	1292	Mar 7, 2016 by taz 76regal
	Flex-A-Lite Elecric Fan Install ,..???? (Preview) Has anyone had any experience with installing a ( Pusher ) Flex-A-Lite electric fan on their radiator, ?? They come with a set of 4 plastic bolts, and fast nuts. I have a problem with the idea of feeding a small philips screw driver through the core of a brand new aluminum radiator, ( as the installat...	cheyenne	24	2154	Mar 6, 2016 by cheyenne
	TH 350 Trany Rebuild (Preview) What upgrades should be considered when getting a mid 70's 350 TH transmission rebuilt for street use?	South Shore	11	1632	Mar 2, 2016 by RacerRick
	looking for a scanner (Preview) I have a snap-on m2500 but it won't work on the 07 chevy and I don't want to spend a lot of money for the cables and cartridge. I have a code reader but am looking for a decent scanner that will give me live data that shows tps etc. and not cost me a lot of $$$$. Any suggestions?	Rustynuts	3	1300	Mar 1, 2016 by Rustynuts
	Brake drums for 9" (Preview) Gidday folks, I have a small bearing 9" rear diff from a 67 Fairlane with 10"x 2.5" brakes. I got the rear end w/o the drums. I'm looking for drums to fit and I can get the proper ones but the money they want for them is outrageous ( Carquest $173 per). Are there any late model drums they w...	willys392	6	1377	Feb 24, 2016 by parklane
	Ford 302 EGR plate gasket fit (Preview) Hi folks, I bought the Edelbrock 4 bbl EGR plate for the 302 and have found that the gasket that goes under it has an opening that is a bit too long on the supply side to the EGR valve and extends to the downstream side by about 1/8 of an inch, creating a situation where exhaust gas can bypass the EGR valve enti...	Randyr	5	1730	Feb 23, 2016 by 427CARL
	Father & Son In Need of Help With Their 72 Dart Swinger (Preview) http://www.kijiji.ca/v-classic-cars/city-of-toronto/72-swinger-looking-for-...	Whitey	12	1728	Feb 22, 2016 by RacerRick
	1934 Plymouth PE (Preview) Just had a call from a guy about his 34 Plymouth he just got, he's trying to find out what the PE model stands for??? I remember when I worked for Chrysler back in the late 60's that they had a P series some ended in a F ?? Anybody know the answer?? Thks Pete	dualquadpete	4	1900	Feb 22, 2016 by 427CARL
	Dual Exhaust Inline 6 - Split Manifold or Headers (Preview) I am considering options for an upcoming engine swap. I want to add dual exhaust to a 235 Chevy I6. I like the look of a split manifold, but I'm concerned it won't flow well enough. I also don't have the ability to weld cast iron so I'd have to find a shop to do it. Of course, I could bolt on Fenton headers and be...	wbeaton	14	4275	Feb 21, 2016 by fleet 51
	51 Merc Work done to date 76 Cougar frt clip welded to 51 Merc frame & engine installed. (Preview) After months of research and measurements I think I have found a donor car. 1976 Ford Cougar, Florida car. wheelbase is very close side to side. saved everything, power windows, brake booster heater core & fan etc. will post some pics once I get the body off. -- Edited by stang on Monday 28th of Marc...	stang	8	2578	Feb 2, 2016 by toomuchjunk
	Lizard Skin (Preview) Has anyone ever made their own sound deadener?? I've done a little web search and apparently this stuff is easy to make, just thought I would ask if anyone here has tried and if it worked out as expected or advertised? Angelo	V2addict	8	1612	Feb 1, 2016 by Rochie
	AIR / FUEL Meters (Preview) I 've seen these meters shown in magazines -- Is it just a matter of installing an O2 sensor in header and connecting it to the guage ?? Somehow it all sounds too simple -- But , I have zero knowledge of these things -- Would enjoy some pointers --- THANKS in Advance -- DON / Fleet 51	fleet 51	7	1461	Jan 19, 2016 by fleet 51
	custom wheels (Preview) does anyone know of any companies still in business who still make custom offset wheels?	Seeker1056	5	1994	Jan 8, 2016 by stang
	Lift on '54 Ford front end. (Preview) Anyone have any experience adding some lift to a '54 ford front end ?? Nothing too radical,..( approx. 2" ),..don't want it looking like a " Gasser ". I can jack the ass end up by using Gabriel ( Rear ) air shocks manufactured for the car,..can't seem to find any for the front, and I don'...	cheyenne	18	1970	Jan 6, 2016 by cheyenne
	Noisy 3.8 buick ultra motor (Preview) I am on my 3rd. buick supercharged motor (all different years) they all have motor knock under load, gas milage is good, no oil burning. put 60,000 klix on last one.anybody else have similar problem?	sherlock	19	1994	Jan 3, 2016 by wuga
	bolts (Preview) anyone out there know how to take the hardness out of a bolt I have several control arm bolts seized into the sleeve/bushings and will have to use a sawzall to cut them out - problem is they are Grade 8 hardness and eat sawzall blades like no tomorrow is there something I can do on the car to remove some or al...	Seeker1056	14	1856	Jan 1, 2016 by Smokin Joe
	WANTED (Preview) Looking for a 57 Chev 2dr. builder. No motor and transmission ok. Not looking for perfect but don't want junk.	tc	2	1500	Dec 23, 2015 by tc
	windshield squirters (Preview) my 90 chevy pu needs more pressure since it only sprays at the bottom ....I have new adjustable nozzles and are pointed as high as they will go. probably pump is worn being 25 yrs old but would rather use a pump unit from a newer vehicle. Any ideas ?	Rustynuts	13	1271	Dec 21, 2015 by Rustynuts
	To bag or not to bag (Preview) I have an after market parallel leaf kit in my 39 Ford coupe and the springs ride flat which results in a rather stiff ride. I like the ride height so I don't want to re arc the springs so my plan is to remove a couple of leaves and install air bags to retain the ride height ,hoping this will smooth the ride. Ha...	hotrod-steve	12	1759	Dec 14, 2015 by Moobster
	motor/cab interferance help (Preview) So I go to put my cab on the frame today as I had some extra people around to help. As you can see in the pictures the cab hits the dist. before the mount holes line up. I still need to move the cab forward about 2-2 1/2". Currently the motor mounts are welded in line and on top of the front cross member....	Marten	24	2113	Dec 10, 2015 by hotrod-steve
	Carbon fiber hood (Preview) I was at a buddies shop a couple years ago. He runs Quick32 @ 7 seconds or some such. Anyway, we were having a beverage or 10 putting the car back together for it's morning load and go. First time I even saw his new car btw. When we're all done, except a door, he says grab that door hanging on the wall. Ya full do...	supernash	0	1113	Dec 5, 2015 by supernash
	Glass (Preview) Can anyone tell me if there is a way to refurbish original glass, I have the original front windshield out of my 1956 F-100 and it has a line where the windshield wipers were, it is as if the blade was worn out and the wiper arm was allowed to sit on the window. Thank you, Angelo	V2addict	1	1267	Nov 29, 2015 by sageygts
	load levelers (Preview) I have a 2014 F250 diesel crew cab short box. I am towing a large 5th wheel with a hitch weight of about 2000 lbs. When I hook up, my bumper drops about 4". I would like to install a set of load leveling shocks to prevent the drop and as well stop the up and down oscillation on bumpy roads. Does anyone...	wuga	13	1501	Nov 28, 2015 by wuga
	Trany Dyno (Preview) Does anyone know of a shop that has a trany dyno that can check the operation of an automatic transmission?	South Shore	2	1254	Nov 24, 2015 by RacerRick
	Learning how to weld!! welding fabrication metal school lessons (Preview) Iam learning how to weld from this awesome new school. The rates are cheap and in a few months your a certified welder. You can what ever you want have your own business or get a job right away. just thought id say something because I find its an awesome help now when Iam fabricating or welding something on...	LT	7	2168	Nov 22, 2015 by Cat in the Hat
	rusted rotors (Preview) I've seen this happen on so many late model cars. The rear rotors rust up because the sliders seize. The pads are like new but they say the rotors must be replaced. How do you get around repairing the surface of the rotors so the rear brakes function, which they never do and that is why the problem in the...	wuga	4	1538	Nov 21, 2015 by 427CARL
	cat converter question (Preview) my 90 chevy has been noisy lately so today I see that there is a small about 1-1/4" dia plug that is on the bottom of the cat that is loose rusted and rattling. Why is there such a plug on a catalytic converter?	Rustynuts	3	1390	Nov 15, 2015 by Sniper
	Adjustable Air Shocks (Preview) Hi guys, I am trying to decide which way to go with the rear suspension of my '59 Apache. I want to keep the leafs but I am wondering if anyone has used air shocks. I am looking at the Monroe Max-Air shocks. The description indicates that they are more meant for leveling a load for towing or heavy loads...	apachomatic	9	1779	Nov 14, 2015 by dualquadpete
	S10 rearend swap (Preview) Well the rearend seized up on my sons s10 pickup. I hve been reading that the way to go on this is to pickup a Ford Explorer rear and the bonis is it bolts up and has disks as well . There is talk about the offset pumpkin causing issues and others say no problem. I understand the bolt pattern is different and it...	flatblack55delivery	6	1854	Nov 14, 2015 by flatblack55delivery
	454 Chev to a 700R 4? (Preview) I have a 454 and want to use a 700R4. What flex plate do I use? The motor is stock and the trans has been beefed up.	hotrod-steve	25	2859	Nov 6, 2015 by hotrod-steve
	Can't access all the replies to my antifreeze question? (Preview) I put a question on the tech forum about antifreeze. Got some good replies, thank you. I was unable to access more than half of them. Still getting email notification on people replying but when I click on them to see them they are not on the forum page. People tried to help me access them with numerous su...	South Shore	2	1459	Nov 1, 2015 by poncho62
	wiring harness (Preview) Anyone out there know of a reasonable supplier here in Ontario for hot rod wiring harnesses? 12 circuit or more also looking for someone who does the LS motor harness rewire service new project is going to be modern efi and automatic OD if it kills me lol	Seeker1056	1	1343	Oct 28, 2015 by Lightspeed Mike
«First < 1 … 5 6 7 8 9 … 17 > Last» \| Page of 17 sorted by