Tech

Bryan · Bryan

What evaporator units are you using in your hot rods for cooling and heating . Looking for something to fit up under the dash . Have looked at using a unit from the rear of a suburban and possible mount under the rear package tray . thanks Bryan

Homer · Homer

I have a nine inch ford rear end in my pickup that has drum brakes and I would like to convert to disc brakes.Yes I can buy a kit but some one told me that you could buy the parts from a wrecker.Has any one done it this way and what year of parts do I look for. Homer

just dave · just dave

Hey guys I'm switching the front end of my 52 chev p/u and am in need of advice/ help The original straight axle was removed entirely and replaced with a independant front suspension out of a 81 chev p/u The new one is 1" wider on the frame than the old, and it makes the truck look like a gasser at the mo...

captainq · captainq

So now that the crusing season is winding down, hopefully not for a few weeks though, I am going to be looking for someone to redo the seat and door panels in my 59 elcamino. I can bring the parts to them and I have purchased three hides of leather. I want a good job but of course dont want to break the bank e...

Seeker1056 · Seeker1056

ok, so trying to finish my interior - and the seat trims are made of polypropelene plastic Is there anything out there that will make paint or glue stick to this stuff? I need to make them a different shade of grey I already tried various spray adhesives in the hopes of covering them with the same seat m...

MANCAVER · MANCAVER

What's the best way to cut up to 3" holes in 1/8 aluminum and also to cut curves in 1/8" aluminum sheet? I was going to try a router on a medium speed. Do you think that would work? Thanks.

69SD · 69SD

I have a left and right tinted door glass from a GM something not sure. Anybody know what they are from ? I want to sell them ! They say Soft Ray on them Thanks a million Kevin

sasquatch · sasquatch

Does anyone have a link to an article about "Beatty and Woods" 302 powered Maverick they ran i think in either C/gas or C/mp. Tried to locate this here by google but not much on this car comes up. Thanks.

scott420p · scott420p

I'm looking for a carburetor for my 350 that will have all the emissions equipment for 1980. I've come across a Holley 4166-1 carb dated 0989. All the info I can find is that its a 4160 600cfm vac secondary off a Chrysler. Here a a couple pics. My question would be is this a decent choice to run on a 350 with a 2...

hemikev · hemikev

picked this up at rocton. its a tilt . column shift but no indicator .what year and make chevy it fit.. i dont really like the shifter there. but has tilt and price was right.... if some 1 lpokin for this and can replace.p m me..

hemikev · hemikev

So , Slim was at my home , we were out looking at my T bucket frame , well Slim thought something out of whack with it , asked if he could take it and check it out , before you know it its at his house on a jig , sure enough its out of whack , well 5 days later it just arrived back at my house , he did amazing work , gu...

henrys57wagon · henrys57wagon

http://www.powdercoatguide.com/2012/11/welcome-to-powder-coating-complete-guide.html#.UjxJ3FMgqQl

34guy · 34guy

Changing the king pins on a 52 chev axle. Installing the new pins Bushing are to size of pin already ,And bushing slips into spindle without to much effort, I am happy with the fit of pin and bushing ,but somewhat concerned the bushing may spin in the spindle mis aligning the grease nipple hole . Should th...

48chev · 48chev

Hey guys I need some help I have a pin hole leak and coolant is coming out on the front passenger side of my motor it looks like a plug is this a frost plug? if so how would you fix it? motor is a 1987 chevy 305 any help would be great Thanks

48chev · 48chev

TBI to carb swap Anyone done it? how did it work out? I would to swap my 1987 chevy 305 TBI to Carb what do you think?

shag766 · shag766

ok hemi i got off his thread to be polite, imagine that. back to the caustic cleaning thingy. sorry newagerod for the jack-up here but; hemi43 "you have some splaining to du here loocy" LOL *dezi* x-ok, after putting my 2 cents in on newrods inquiry about hardware and i mentioned i'd like...

flatblack55delivery · flatblack55delivery

We have something of a problem on an LT1 engine. while driving the Roadmaster home The Boy had it really get noisie but did get it home.We looked and found the #1plug wire and half the plug had fallen out.The plug is broken of just below the nut with the threds and electrode still in the head.Looks like...

Builderrhys · Builderrhys

I am trying to bend some Drawn Over Mandrel (DOM) tubing and I am not having much luck with the good quality pipe bender (Enerpac) that I thought I could squeak by with. The DOM is kinking in the center of the bend. I don't have a pile of cash to spend on a bender right now and I don't know of anyone in my ar...

MANCAVER · MANCAVER

Anyone have any experience with Atlas lifts or Greg Smith Equipment Co.?

RacerRick · 77

I hate searching the web for stuff . I always come up with dead ends . does any one have a link to a decent site with info on nitrous install on a hatch back style body with no separate trunk .. Thanks ..77.

GP CUTLASS · GP CUTLASS

Hi Guys. 1970 Cutlass 350 rocket The last couple of days the "HOT" light for the engine has been flickering off and on when I slow down. It's not on when I am driving. It's not on when I stop. It happens when I am slowing down to stop. Any ideas? -- Edited by GP CUTLASS on Wednesday 21st of August 20...

Chevypkup66 · Chevypkup66

Thanks for the suggestions. Finally got around to having time to check it out closer. It was a broken wire to the ignition. Put new wire in with inline fuse and all is great. Glad to be driving my baby again. Thanks again.

sasquatch · sasquatch

Just reading a write up in Doug Boyce's great book about Junior Stocks. "Tim Nega" ran a 55 Chev with a "STOCK: 265 , 162 HP ,2 barrel carb, and a 3 speed stick, A legal NHRA record holder . Amazing that this car was running a 5:86 rear end, and the three speed stick trans low gear ratio was a 3...

Gearhead · Gearhead

Ok, so the wife's van just developed a noise that concerns me. When you kill the engine, there is a ringing, metallic noise that continues for 2-3 seconds after the engine stops. What it sounds like to me is something metal still spinning making a ringing noise as if it was a big washer on a shaft or someth...

scott420p · scott420p

My mothers 2003 saturn l200 keeps blowing the front ds wheel bearing(and its a PITA to fix). A couple of winters ago I was driving it in the winter and I was an ass and slid it into a curb. I replaced the wheel bearing and the bent rim and everything was alright for about a year, then went again. So I/my mother...

poncho62 · poncho62

I just bought this today. Got it for a good price because it has had water leaks.....Asking Pete or whoever wishes to voice their expertise. It seems that the seam on the roof across the front of the rubber roof where it joins the aluminum split and let water in over the winter...Here is the resulting dam...

slim · slim

Talking to a buddy from the falls today , he has a 62 235 points setup. Good spark from the coil(new ) weak or no spark at the plug(new points, condenser , cap, wires,plugs). now heres the twist if he pulls the plug off the block he gets a good sharp spark between the plug body and block. coil is hooked up ri...

GP CUTLASS · GP CUTLASS

Hey guys. I'm not trying to rush through the summer. Just wondering how you store your cars for the winter?

rectob · rectob

Driving home and truck was running great. Put in third and it stuck. Now it won't come out of third. I am very non-mechanical...if anyone lives near Barrie or knows a decent mechanic, let me know? Thanks all!

Cat in the Hat · Cat in the Hat

I changed the oil in my hot rod to full synthetic....and now every now and then huffs oil smoke out the exhaust. Im changing back to a quality regular oil and I'll let you know if it stops. Anyone else with this problem?

sasquatch · sasquatch

Just for the heck of it here is what a vacuum gauge will tell you. Exhaust or intake valve sticking. Sparkplug misfiring. Burned exhaust or intake valve. Piston rings or cylinder walls worn. Ignition timing off. Valve timing off. Valve timing off due to worn camshaft lobe or timing gear. Intake gaske...

hemi43 · hemi43

I put one on my car years ago, but never liked the feel of it. The main issue I'm having is I get a lot of feedback to my steering wheel when I hit fairly large bumps only on one wheel. I'm blaming this ona rather small KPI, thus giving me a large scrub radius (4-5 inches). Anyone else have this problem? Other...

427CARL · 427CARL

The 1949 from Colorado seem to have a high altitude, attitude... We cleaned the gas tank added fresh fuel We changed plugs, wires, and cap and rotor, and coil (6V) The truck will run very rough, and a little better if vaccum line pulled off... The carb is a Carter YF 2100S We cleaned it and made sure...

30AV8 · 30AV8

I'm having my pickup re-painted, and I am doing the prep work. the paint on there now is an enamel(acrylic?) of some sort. some panels are fine and i was just going to rough up the paint with like 600-800 grit, while other panels have some filler work to be done. with these i am sanding down either to the met...

janies dirty 37 · janies dirty 37

Question for anyone who has chopped there ride ??? Where did you get new windshield and other glass from?? No one will "tackle that big of a job" around here

Any ideas/input would be appreciated

Janice

Gazoo · Gazoo

I'm not sure what forum this belongs under, but...I need help. I picked up an old "MERCURY" battery charger/tester on my way back from Syracuse last weekend, I took it apart today to restore it, but I can't find any dates what-so-ever. I took a bunch of pics, as I always do, before I start tear...

oldkoot · oldkoot

Trying to help a friend, 39 Plymouth with a 5.7 Hemi that came out of a 2004 Magnum. Problem started out as intermittent no start last year( just like a dead battery, nothing), leave it for an hour and fired right up and ran fine, replaced ECM and had VATs disabled thinking this might be the problem. Now st...

48chev · 48chev

Hey what are you guys using for wiper motors ? Im working on 1948 chev pick up and was thinking of using a wiper motor from the rear window of a caravan do you think it will work ?

Gwillyville Kid · Gwillyville Kid

Many years ago I heard about how a Corvette could burn to the ground in 3 minutes. Gasoline plus resin from fiberglass and other flammable items such as upholstery, wiring plastic covering tires all combine for one Jim Dandy fire. I attended a seminar about automotive wiring and electrical compone...

Beachcat · Beachcat

These came with an HID headlight kit. It's bizaarr

Dave Scott · Dave Scott

So my AC was working when I got the truck in March, but now when I need it, it's not working. I bought the re-seal recharge and hose kit, but when I hooked it up, it's already showing full pressure. The compressor clutch spins as it should when the engine is running, and there's air blowing inside the cab, b...

Rustynuts · Rustynuts

need to reglue my truck headliner and was wondering if there are good/bad glues . 3m 77 comes up on the net but some like it some don't ...as does permatex super that crappy tire sells.

Rustynuts · Rustynuts

got the tranny back in the 46 and went to start it and pop goes the starter fuse. ...checked all wires and none are bare ,pinched .....I did do a wire cleanup on the wires going to the starter but they are all ok....now I'm wondering if its a shorted starter solenoid..the solenoid doesn't even engage.......

captainq · captainq

Gave my rochester 4 jet carb off my 348 engine to a mechanic to rebuild. Got the kit and he disassembled it but both floats had gas in them. Cant seem to find replacement floats, Any chance someone may have one of these carbs with good floats or another carb that may fit my intake. It is basically two tw...

Cat in the Hat · Cat in the Hat

Had it rebuilt....5000 miles ago......runs good...full manual....but Every now and then...not all the time...when I back out of the garage...it pukes tranny fluid while in reverse WTF? I find a puddle under the car when parked every now and then ...sometimes a few drops...sometimes a lake Any t...

poncho62 · poncho62

A bit off topic.....I am going camping in a couple of weeks. Taking our popup trailer and will have no electric. I will be running the campers lights and water pump on batteries. I have one on board RV battery and an going to take a 2nd, maybe a 3rd. Heres the question...Which will last longer....Hook the...

Gwillyville Kid · Gwillyville Kid

I am trying to identify these ground brackets. The 8 finger one is from a 80's G20 van, and mounts on the boot that seal s the firewall where the steering column passes through. The 6 finger unit is from and 80's S10 and I believe it mounts on the parking brake mounting bracket on the driver's kick panel. I...

Adslow65 · Adslow65

Hey everyone, I picked up this front straight axle off a truck (good deal, it was just the axle - no truck and the guy wasn't sure what it was from) I was hoping to use it for a project... I thought it was Ford but I think I made a bone head move, as this one might be Dodge!? Can anyone help me identify this for sur...

crash43 · crash43

Trans won't shift out of first gear so I went through my check list: replaced vacuum line and modulator checked governor gear ( it was good ) replaced fluid and put new filter an...

r680680 · r680680

Well I decided I want to put disk brakes front and back and upgrade to power steering on my 56 nomad. But there is a lot of different makes and sizes out there. Just want to get feed back from others that have done sim work on there ride

Topic		Started By	Replies	Views	Last Post
	Re: A/C heater evaporators (Preview) What evaporator units are you using in your hot rods for cooling and heating . Looking for something to fit up under the dash . Have looked at using a unit from the rear of a suburban and possible mount under the rear package tray . thanks Bryan	Bryan	7	1582	Oct 12, 2013 by JohnnyBgood
	Rear disc brakes for nine inch ford (Preview) I have a nine inch ford rear end in my pickup that has drum brakes and I would like to convert to disc brakes.Yes I can buy a kit but some one told me that you could buy the parts from a wrecker.Has any one done it this way and what year of parts do I look for. Homer	Homer	18	5973	Oct 10, 2013 by johnod
	Front end swap help (Preview) Hey guys I'm switching the front end of my 52 chev p/u and am in need of advice/ help The original straight axle was removed entirely and replaced with a independant front suspension out of a 81 chev p/u The new one is 1" wider on the frame than the old, and it makes the truck look like a gasser at the mo...	just dave	39	4435	Oct 7, 2013 by Ziggy
	upholstery (Preview) So now that the crusing season is winding down, hopefully not for a few weeks though, I am going to be looking for someone to redo the seat and door panels in my 59 elcamino. I can bring the parts to them and I have purchased three hides of leather. I want a good job but of course dont want to break the bank e...	captainq	2	909	Oct 5, 2013 by slab
	polypropelene plastics (Preview) ok, so trying to finish my interior - and the seat trims are made of polypropelene plastic Is there anything out there that will make paint or glue stick to this stuff? I need to make them a different shade of grey I already tried various spray adhesives in the hopes of covering them with the same seat m...	Seeker1056	4	993	Oct 5, 2013 by oldkoot
	cutting aluminum (Preview) What's the best way to cut up to 3" holes in 1/8 aluminum and also to cut curves in 1/8" aluminum sheet? I was going to try a router on a medium speed. Do you think that would work? Thanks.	MANCAVER	14	2436	Oct 4, 2013 by Mr Samis
	Tinted door glass what is it from ? (Preview) I have a left and right tinted door glass from a GM something not sure. Anybody know what they are from ? I want to sell them ! They say Soft Ray on them Thanks a million Kevin	69SD	1	786	Sep 30, 2013 by 77
	Beatty and Woods: (Preview) Does anyone have a link to an article about "Beatty and Woods" 302 powered Maverick they ran i think in either C/gas or C/mp. Tried to locate this here by google but not much on this car comes up. Thanks.	sasquatch	6	4302	Sep 26, 2013 by Dick Kirkpatrick
	Thoughts on a Holley carb (Preview) I'm looking for a carburetor for my 350 that will have all the emissions equipment for 1980. I've come across a Holley 4166-1 carb dated 0989. All the info I can find is that its a 4160 600cfm vac secondary off a Chrysler. Here a a couple pics. My question would be is this a decent choice to run on a 350 with a 2...	scott420p	7	1361	Sep 25, 2013 by sasquatch
	wheel and Columm. .what year and model (Preview) picked this up at rocton. its a tilt . column shift but no indicator .what year and make chevy it fit.. i dont really like the shifter there. but has tilt and price was right.... if some 1 lpokin for this and can replace.p m me..	hemikev	3	825	Sep 24, 2013 by hemikev
	Tech , good guy alert (Preview) So , Slim was at my home , we were out looking at my T bucket frame , well Slim thought something out of whack with it , asked if he could take it and check it out , before you know it its at his house on a jig , sure enough its out of whack , well 5 days later it just arrived back at my house , he did amazing work , gu...	hemikev	17	1221	Sep 21, 2013 by hemikev
	powder coating blog, not mine!!!!!! (Preview) http://www.powdercoatguide.com/2012/11/welcome-to-powder-coating-complete-guide.html#.UjxJ3FMgqQl	henrys57wagon	1	788	Sep 20, 2013 by hemi43
	king pin questions (Preview) Changing the king pins on a 52 chev axle. Installing the new pins Bushing are to size of pin already ,And bushing slips into spindle without to much effort, I am happy with the fit of pin and bushing ,but somewhat concerned the bushing may spin in the spindle mis aligning the grease nipple hole . Should th...	34guy	26	1539	Sep 19, 2013 by fatstax
	Coolant Leak (Preview) Hey guys I need some help I have a pin hole leak and coolant is coming out on the front passenger side of my motor it looks like a plug is this a frost plug? if so how would you fix it? motor is a 1987 chevy 305 any help would be great Thanks	48chev	12	1127	Sep 17, 2013 by 48chev
	TBI to carb swap (Preview) TBI to carb swap Anyone done it? how did it work out? I would to swap my 1987 chevy 305 TBI to Carb what do you think?	48chev	18	1848	Sep 16, 2013 by fatstax
	caustic cleaning (Preview) ok hemi i got off his thread to be polite, imagine that. back to the caustic cleaning thingy. sorry newagerod for the jack-up here but; hemi43 "you have some splaining to du here loocy" LOL dezi x-ok, after putting my 2 cents in on newrods inquiry about hardware and i mentioned i'd like...	shag766	23	1889	Sep 14, 2013 by 2inchestoolow
	Lt1 broken plug (Preview) We have something of a problem on an LT1 engine. while driving the Roadmaster home The Boy had it really get noisie but did get it home.We looked and found the #1plug wire and half the plug had fallen out.The plug is broken of just below the nut with the threds and electrode still in the head.Looks like...	flatblack55delivery	21	1248	Sep 13, 2013 by atomsplitter
	Tubing Bender (Preview) I am trying to bend some Drawn Over Mandrel (DOM) tubing and I am not having much luck with the good quality pipe bender (Enerpac) that I thought I could squeak by with. The DOM is kinking in the center of the bend. I don't have a pile of cash to spend on a bender right now and I don't know of anyone in my ar...	Builderrhys	24	5926	Aug 31, 2013 by sasquatch
	atlas lifts (Preview) Anyone have any experience with Atlas lifts or Greg Smith Equipment Co.?	MANCAVER	0	1051	Aug 30, 2013 by MANCAVER
	Nitrous install question (Preview) I hate searching the web for stuff . I always come up with dead ends . does any one have a link to a decent site with info on nitrous install on a hatch back style body with no separate trunk .. Thanks ..77.	77	37	2630	Aug 26, 2013 by RacerRick
	HOT light (Preview) Hi Guys. 1970 Cutlass 350 rocket The last couple of days the "HOT" light for the engine has been flickering off and on when I slow down. It's not on when I am driving. It's not on when I stop. It happens when I am slowing down to stop. Any ideas? -- Edited by GP CUTLASS on Wednesday 21st of August 20...	GP CUTLASS	3	712	Aug 22, 2013 by dualquadpete
	Dead truck up and running (Preview) Thanks for the suggestions. Finally got around to having time to check it out closer. It was a broken wire to the ignition. Put new wire in with inline fuse and all is great. Glad to be driving my baby again. Thanks again.	Chevypkup66	42	30855	Aug 20, 2013 by Ziggy
	Those incredible Junior Stocks: (Preview) Just reading a write up in Doug Boyce's great book about Junior Stocks. "Tim Nega" ran a 55 Chev with a "STOCK: 265 , 162 HP ,2 barrel carb, and a 3 speed stick, A legal NHRA record holder . Amazing that this car was running a 5:86 rear end, and the three speed stick trans low gear ratio was a 3...	sasquatch	10	1257	Aug 20, 2013 by sasquatch
	Spinning metal noise after shut off?? (Preview) Ok, so the wife's van just developed a noise that concerns me. When you kill the engine, there is a ringing, metallic noise that continues for 2-3 seconds after the engine stops. What it sounds like to me is something metal still spinning making a ringing noise as if it was a big washer on a shaft or someth...	Gearhead	10	1402	Aug 20, 2013 by Chris Stapley
	Question About a DD (Preview) My mothers 2003 saturn l200 keeps blowing the front ds wheel bearing(and its a PITA to fix). A couple of winters ago I was driving it in the winter and I was an ass and slid it into a curb. I replaced the wheel bearing and the bent rim and everything was alright for about a year, then went again. So I/my mother...	scott420p	30	1629	Aug 18, 2013 by scott420p
	RV help needed (Preview) I just bought this today. Got it for a good price because it has had water leaks.....Asking Pete or whoever wishes to voice their expertise. It seems that the seam on the roof across the front of the rubber roof where it joins the aluminum split and let water in over the winter...Here is the resulting dam...	poncho62	21	1449	Aug 18, 2013 by workin class
	Spark (Preview) Talking to a buddy from the falls today , he has a 62 235 points setup. Good spark from the coil(new ) weak or no spark at the plug(new points, condenser , cap, wires,plugs). now heres the twist if he pulls the plug off the block he gets a good sharp spark between the plug body and block. coil is hooked up ri...	slim	20	1101	Aug 16, 2013 by slim
	winter storage (Preview) Hey guys. I'm not trying to rush through the summer. Just wondering how you store your cars for the winter?	GP CUTLASS	29	1330	Aug 14, 2013 by janies dirty 37
	1968 GMC Pick up 3 in the tree (Preview) Driving home and truck was running great. Put in third and it stuck. Now it won't come out of third. I am very non-mechanical...if anyone lives near Barrie or knows a decent mechanic, let me know? Thanks all!	rectob	6	1227	Aug 13, 2013 by IR Mechanik
	Synthetic oil Problems (Preview) I changed the oil in my hot rod to full synthetic....and now every now and then huffs oil smoke out the exhaust. Im changing back to a quality regular oil and I'll let you know if it stops. Anyone else with this problem?	Cat in the Hat	21	7502	Aug 11, 2013 by shag766
	The Vacuum gauge: (Preview) Just for the heck of it here is what a vacuum gauge will tell you. Exhaust or intake valve sticking. Sparkplug misfiring. Burned exhaust or intake valve. Piston rings or cylinder walls worn. Ignition timing off. Valve timing off. Valve timing off due to worn camshaft lobe or timing gear. Intake gaske...	sasquatch	12	3203	Aug 8, 2013 by scott420p
	Anyone using a TCI or equivalent front end on their car?? (Preview) I put one on my car years ago, but never liked the feel of it. The main issue I'm having is I get a lot of feedback to my steering wheel when I hit fairly large bumps only on one wheel. I'm blaming this ona rather small KPI, thus giving me a large scrub radius (4-5 inches). Anyone else have this problem? Other...	hemi43	4	1055	Aug 5, 2013 by hemi43
	1949 Chevrolet 3100 from Colorado (Preview) The 1949 from Colorado seem to have a high altitude, attitude... We cleaned the gas tank added fresh fuel We changed plugs, wires, and cap and rotor, and coil (6V) The truck will run very rough, and a little better if vaccum line pulled off... The carb is a Carter YF 2100S We cleaned it and made sure...	427CARL	6	1008	Aug 5, 2013 by sasquatch
	painting question (Preview) I'm having my pickup re-painted, and I am doing the prep work. the paint on there now is an enamel(acrylic?) of some sort. some panels are fine and i was just going to rough up the paint with like 600-800 grit, while other panels have some filler work to be done. with these i am sanding down either to the met...	30AV8	16	1312	Aug 4, 2013 by slab
	SOS!!! Where to get new windshield/glass for chopped (Preview) Question for anyone who has chopped there ride ??? Where did you get new windshield and other glass from?? No one will "tackle that big of a job" around here Any ideas/input would be appreciated Janice	janies dirty 37	18	4332	Aug 1, 2013 by fatstax
	Need help identifying. (Preview) I'm not sure what forum this belongs under, but...I need help. I picked up an old "MERCURY" battery charger/tester on my way back from Syracuse last weekend, I took it apart today to restore it, but I can't find any dates what-so-ever. I took a bunch of pics, as I always do, before I start tear...	Gazoo	6	939	Jul 28, 2013 by henrys57wagon
	Will it start?? maybe, maybe not, it's a MOPAR!! (Preview) Trying to help a friend, 39 Plymouth with a 5.7 Hemi that came out of a 2004 Magnum. Problem started out as intermittent no start last year( just like a dead battery, nothing), leave it for an hour and fired right up and ran fine, replaced ECM and had VATs disabled thinking this might be the problem. Now st...	oldkoot	8	1038	Jul 27, 2013 by oldkoot
	wiper motor (Preview) Hey what are you guys using for wiper motors ? Im working on 1948 chev pick up and was thinking of using a wiper motor from the rear window of a caravan do you think it will work ?	48chev	12	1103	Jul 27, 2013 by 77
	Use Fuses! (Preview) Many years ago I heard about how a Corvette could burn to the ground in 3 minutes. Gasoline plus resin from fiberglass and other flammable items such as upholstery, wiring plastic covering tires all combine for one Jim Dandy fire. I attended a seminar about automotive wiring and electrical compone...	Gwillyville Kid	8	1303	Jul 23, 2013 by Cat in the Hat
	Check out these intall instructions lol (Preview) These came with an HID headlight kit. It's bizaarr	Beachcat	6	829	Jul 22, 2013 by bygddy
	1998 F150 AC help please (Preview) So my AC was working when I got the truck in March, but now when I need it, it's not working. I bought the re-seal recharge and hose kit, but when I hooked it up, it's already showing full pressure. The compressor clutch spins as it should when the engine is running, and there's air blowing inside the cab, b...	Dave Scott	13	1565	Jul 20, 2013 by Dave Scott
	headliner glue (Preview) need to reglue my truck headliner and was wondering if there are good/bad glues . 3m 77 comes up on the net but some like it some don't ...as does permatex super that crappy tire sells.	Rustynuts	7	1489	Jul 20, 2013 by 427CARL
	blowing fuses!!!!! (Preview) got the tranny back in the 46 and went to start it and pop goes the starter fuse. ...checked all wires and none are bare ,pinched .....I did do a wire cleanup on the wires going to the starter but they are all ok....now I'm wondering if its a shorted starter solenoid..the solenoid doesn't even engage.......	Rustynuts	12	6899	Jul 18, 2013 by DaveM
	Rochester 4 jet carb (Preview) Gave my rochester 4 jet carb off my 348 engine to a mechanic to rebuild. Got the kit and he disassembled it but both floats had gas in them. Cant seem to find replacement floats, Any chance someone may have one of these carbs with good floats or another carb that may fit my intake. It is basically two tw...	captainq	14	2170	Jul 17, 2013 by poncho62
	Any tranny guys out there.......th350 question (Preview) Had it rebuilt....5000 miles ago......runs good...full manual....but Every now and then...not all the time...when I back out of the garage...it pukes tranny fluid while in reverse WTF? I find a puddle under the car when parked every now and then ...sometimes a few drops...sometimes a lake Any t...	Cat in the Hat	5	1367	Jul 16, 2013 by slim
	Battery question (Preview) A bit off topic.....I am going camping in a couple of weeks. Taking our popup trailer and will have no electric. I will be running the campers lights and water pump on batteries. I have one on board RV battery and an going to take a 2nd, maybe a 3rd. Heres the question...Which will last longer....Hook the...	poncho62	7	910	Jul 16, 2013 by 3 deuce
	Chevy & GMC Ground Bracket (Preview) I am trying to identify these ground brackets. The 8 finger one is from a 80's G20 van, and mounts on the boot that seal s the firewall where the steering column passes through. The 6 finger unit is from and 80's S10 and I believe it mounts on the parking brake mounting bracket on the driver's kick panel. I...	Gwillyville Kid	2	902	Jul 14, 2013 by fatstax
	Front axle identification Help! (Preview) Hey everyone, I picked up this front straight axle off a truck (good deal, it was just the axle - no truck and the guy wasn't sure what it was from) I was hoping to use it for a project... I thought it was Ford but I think I made a bone head move, as this one might be Dodge!? Can anyone help me identify this for sur...	Adslow65	10	2648	Jul 14, 2013 by Gwillyville Kid
	Diagnosing a TH350 (Preview) Trans won't shift out of first gear so I went through my check list: replaced vacuum line and modulator checked governor gear ( it was good ) replaced fluid and put new filter an...	crash43	10	4381	Jul 9, 2013 by crash43
	To Many to choose from (Preview) Well I decided I want to put disk brakes front and back and upgrade to power steering on my 56 nomad. But there is a lot of different makes and sizes out there. Just want to get feed back from others that have done sim work on there ride	r680680	4	933	Jul 2, 2013 by henrys57wagon
«First < 1 … 11 12 13 14 15 … 17 > Last» \| Page of 17 sorted by